How to: Rear reflector LED light strip conversion.
Volvo LED lights - this is how I did it after following some previous advice on here - how difficult can it be ???
Ok so here we go - how I fitted 2 LED strips into each of the vertical reflector units above the rear light clusters: #1 Remove light cluster by releasing these two nut/bolts (do not drop them down the skin) http://i1193.photobucket.com/albums/...IMG_6611-1.jpg http://i1193.photobucket.com/albums/...D/IMG_6614.jpg #2 release the bolts holding the vertical strip http://i1193.photobucket.com/albums/...D/IMG_6615.jpg http://i1193.photobucket.com/albums/...D/IMG_6616.jpg #3 Voila - the rectangular strip down the centre is what you're interested in :-) http://i1193.photobucket.com/albums/...D/IMG_6620.jpg Back to this in a minute #4 This is what I used to make the channel to hold the strips in (Wickes if they still do it): http://i1193.photobucket.com/albums/...D/IMG_6622.jpg http://i1193.photobucket.com/albums/...D/IMG_6625.jpg #5 I bought a variety of white and red strips as I didn't know how bright or not they'd look behind the red lens - these flexible strips are what I ended up with: http://i1193.photobucket.com/albums/...D/IMG_6583.jpg http://i1193.photobucket.com/albums/...D/IMG_6602.jpg http://i1193.photobucket.com/albums/...D/IMG_6592.jpg In the end I used 1 red and 1 white strip per side. #6 OK now the deep breath and time to get the Drimmel out. Using a cutting bit I followed the line around the rectangle I mentioned above. I left the 'nipples at each end for a reason which will become apparent in a mo: http://i1193.photobucket.com/albums/...ps3cd9589c.jpg http://i1193.photobucket.com/albums/...ps79cb3ad7.jpg http://i1193.photobucket.com/albums/...ps3c237cd4.jpg http://i1193.photobucket.com/albums/...psc9b40e6f.jpg http://i1193.photobucket.com/albums/...pse4fd82e2.jpg I wasn't sure if I'd need this bit to help position it later - so I kept it in tact and made sure the channel stayed straight along the edge: http://i1193.photobucket.com/albums/...psd5775f0e.jpg #7 Phew! http://i1193.photobucket.com/albums/...ps7fd559af.jpg #8 Measure the length of channel you need: http://i1193.photobucket.com/albums/...ps973f2528.jpg #9 Trim it and use the 'nipples' to help stop it falling into the lense (neat huh!) http://i1193.photobucket.com/albums/...pseca7a1ae.jpg http://i1193.photobucket.com/albums/...psdaa1bc83.jpg repeat for the other end and BINGO http://i1193.photobucket.com/albums/...ps57a32427.jpg "Top" As I'm getting senile in my old age - always helpful to make sure you get things things the right way up - been there, done that and had to buy a new interior door to put it right :-) #10 Ok so now to the LEDS - http://i1193.photobucket.com/albums/...ps7beb99d1.jpg http://i1193.photobucket.com/albums/...psd2c4370c.jpg These are a snug fit side by side - trim to length: http://i1193.photobucket.com/albums/...ps68e390c1.jpg http://i1193.photobucket.com/albums/...ps85e3a184.jpg Make sure you remember which is which when you come to wire them up if you're putting in more than one strip per side (inner to inner etc.) 'cos when you start turning things around it's easy (for me) to forget what's what.. #11 Quick check: (been there done that too) http://i1193.photobucket.com/albums/...psc2170e95.jpg http://i1193.photobucket.com/albums/...ps85e3a184.jpg #12 Hey presto - drop the channel in place with wires at the BOTTOM http://i1193.photobucket.com/albums/...ps9cbfe9fb.jpg http://i1193.photobucket.com/albums/...ps15d0b413.jpg #13 Just to make it as water tight as possible I used some bathroom sealant to hold it all together ( not too pretty - but effective) http://i1193.photobucket.com/albums/...ps809080fb.jpg http://i1193.photobucket.com/albums/...psd48c6443.jpg #14 I soldered some thicker wire to the LED wiring to hook up to the loom in the car - black was common and blue and red to distinguish between drl and brake light http://i1193.photobucket.com/albums/...ps7c4155b1.jpg #15 It really is difficult to tell in these two pictures because of the light - but: DRL: http://i1193.photobucket.com/albums/...ps0cea34ba.jpg DRL + brake http://i1193.photobucket.com/albums/...ps977f6006.jpg #16 Back on the car http://i1193.photobucket.com/albums/...psb4a38db6.jpg I think at this point I got rained off and stopped taking photos and then when I finally got back to it to wire it up I was against the clock. So the final stages were to identify the wires needed in the lighting loom for the DRL's and the brake light + a common earth. Duly crimped together using the blue type fold over and crimp connectors from Halfords. For my sins I do not have a photo of them in action on the car - but I do know that some of the leds have blown since last summer so I need to revisit the strips concerned. Hope that helps - it was worth the effort and does indeed look awesome. Good Luck Cheers Ian. PS I bought the LED strips a few years ago and had been sitting on them 'til last year - so any search on e-bay etc. should find you something the same but at least you know what to aim for. |
looks very good but perhaps a final rear view shot showing the whole tail end would be helpfull for full effect
|
Good how to, thanks
|
Quote:
Cheers Ian. |
Looking forward to seeing a rear end shot of the finished article. Can I ask how much it cost for the materials for this?
|
Top job that is.....I have the LED's off ebay just like those and also the tracking too off a caravan curtain track ! Deep breath and start cutting !
|
That's a great howto
|
Quote:
To be honest - it was such a while ago that I bought the LED's I honestly can't remember. Maybe £20 tops - but I bought several packs to play with so didn't use all of them. The conduit I already had in my garage left over from a house project. Wire and all the other bits etc. again taken from the 'that'll come in handy one day' shelf in the garage. AND who needs an excuse to buy a Drimmel :-) (improvise or borrow one). But just be careful not to break or scratch the lense. I supported it on a bag of soft sand rather than try and grip it with a clamp. Cheers Ian |
Hi Ian
Great right up. Can I ask a couple of silly questions! Did you use the red LED strips for the break lights and the white strip as the DRLs? Or are both strips on constant with the DRLs? If anyone got advice/pics on connecting the wiring that would be great Bob |
Quote:
I went with the inboard strip white connected to DRL. The outboard strip red connected to the brakelights. This is why you need to be methodical because when youput the strips in the channel you then turn them over to put in the lense - you then turn the lense round to put it on either the left or right rear of the car. It's like 'chase the ace' keeping track. To be honest - the difference between the two when lit is marginal. The DRL white strip is a softer red when lit. The red brake light strip brightens it up a bit with both on together. I will try and get back out to finish of the photos soonest - including the wiring connections. cheers Ian. |
All times are GMT +1. The time now is 18:05. |
Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.