Volvo Owners Club Forum

Volvo Owners Club Forum (https://www.volvoforums.org.uk/index.php)
-   PV, 120 (Amazon), 1800 General (https://www.volvoforums.org.uk/forumdisplay.php?f=9)
-   -   Amazon: Throttle linkage - Webcon DGV kit (https://www.volvoforums.org.uk/showthread.php?t=314037)

GaryBray Feb 5th, 2021 18:36

Throttle linkage - Webcon DGV kit
 
3 Attachment(s)
Have just taken delivery of all required to replace the worn Stromberg and cracked manifold on this '64 B20 Amazon Combi ... and at the same time remove the LPG installation and refit a factory type fuel tank ...

Anyone a photo/s showing the throttle linkage set up for the Webcon PVO101 DGV kit?

Derek UK Feb 6th, 2021 14:37

Talk to these guys, they are very accommodating. Tell them what Webcon kit you have.
https://fastroadcars.co.uk/store/ind...product_id=524
There are other suppliers Google Weber 32/36 DGAV or DGV control linkages

Nice Combi!

Laird Scooby Feb 6th, 2021 16:54

Quote:

Originally Posted by GaryBray (Post 2707107)
Have just taken delivery of all required to replace the worn Stromberg and cracked manifold on this '64 B20 Amazon Combi ... and at the same time remove the LPG installation and refit a factory type fuel tank ...

Anyone a photo/s showing the throttle linkage set up for the Webcon PVO101 DGV kit?

All the instructions/adaptors to convert from Stromberg to Weber should be in the conversion kit, they always used to be. Aside from perhaps minor tuning of the idle it should be near enough plug'n'play.

You may have to fit different air correction or main jets though to prevent the top end fueling going lean as i see you also have an extractor manifold which will likely make the top end lean, would have done the same with the old carb and you would have had to change the needle.

Worth a session on a rolling road where they know about Weber progressive twin-choke carbs to get it set up just right too.

Faust Feb 6th, 2021 19:57

I used the linkages that came with the kit when I installed my Weber conversion many years ago.

Don't have any pics and unlikely to have any in the near future as my car is under a cover at the moment as I'm not using it (thanks CV19).

If you don't have them already, get some new ball joint linkages for the pedal linkage where it comes though the bulkhead - makes the job easier when fitting .
It can be tricky to get the linkages just right. Bit of trial and error will get the job done. Just make double sure all linkages are free to move 100% as it can be tricky to get the rod from the bar that leads from the pedal to carb connector just right.

It's a case of messing around with it until all is well really... pretty easy job all in, just a bit fiddly in places.

Mike

GaryBray Feb 8th, 2021 14:51

1 Attachment(s)
Cheers for your input guys ... much appreciated.

I've no issue figuring the linkage out for myself, nor re-jetting the carb if required, just wondered if anyone actually had a photo for reference as no, the Webcon kit supplied had nothing by way of instructions.

Have now hit a more serious snag though. The inlet manifold and exhaust header are not compatible without modification. As seen in these photos the underside of the inlet fouls the centre pipes of the header and therefore will not fit flush to the head ports. NOT what I was expecting !!

When told of the problem via email the supplier [who shall remain nameless at this stage] simply replied , quote :

"Hi Gary, We’ve seen this problem before but unfortunately this is how these are made. You can adjust something yourself to fix it or you could return the manifold and change it for a 4-1 manifold, these fit better."

How's that for customer service !?! lol

Laird Scooby Feb 8th, 2021 15:01

Quote:

Originally Posted by GaryBray (Post 2708172)
Cheers for your input guys ... much appreciated.

I've no issue figuring the linkage out for myself, nor re-jetting the carb if required, just wondered if anyone actually had a photo for reference as no, the Webcon kit supplied had nothing by way of instructions.

Have now hit a more serious snag though. The inlet manifold and exhaust header are not compatible without modification. As seen in these photos the underside of the inlet fouls the centre pipes of the header and therefore will not fit flush to the head ports. NOT what I was expecting !!

When told of the problem via email the supplier [who shall remain nameless at this stage] simply replied , quote :

"Hi Gary, We’ve seen this problem before but unfortunately this is how these are made. You can adjust something yourself to fix it or you could return the manifold and change it for a 4-1 manifold, these fit better."

How's that for customer service !?! lol

Unless you'll constantly be driving in the 4500-6000rpm range, a 4-2-1 manifold will be better than the 4-1 version, giving a wider spread of power and smoother performance overall.

Are you able to relieve the inlet manifold at all to help the clearance or perhaps persuade the exhaust manifold into a different shape?

If it's any consolation, i emailed an ebay seller to query whether they'd had any reported problems with a particular aspect of a product, here's the reply i got :

"Thank you for your enquiry.

Please provide us with your car's registration number so that we may find the correct product for your vehicle.

Our staff is currently working from home office, we are doing our best to assist you during the pandemic. It may take a bit longer for us to reply, we appreciate your patience. "

I'd already ascertained it will fit, it seems they are just too lazy to answer my question! :rolleyes::eek::rolleyes:

Burdekin Feb 8th, 2021 16:48

2 Attachment(s)
Would the cast exhaust manifolds fit?

Burdekin Feb 8th, 2021 16:56

1 Attachment(s)
I think you can just cut the intake manifold section off of your old manifold.

Derek UK Feb 9th, 2021 14:42

The back yard fix is with a hammer to the exhaust and maybe a file to the inlet. Done with a bit of finesse it should solve the problem. The interference looks to be minimal so there should be no negatives. The alloy inlet is pretty thick. You won't see the results of mods when all is fitted back up. This sort if mismatch isn't unusual.

GaryBray Feb 10th, 2021 10:41

1 Attachment(s)
I appreciate that taking a hammer and file to the parts would solve the problem ... but in my humble opinion that's not the point. The underlying issue is that the parts suppliers thenselves should be addressing these problems.

Rather than simply saying 'yeah we know there' s a fitting issue, sort it yourself or send it back' they should be taking the issue back to their own suppliers. Maybe we the end users have become too complacent?

Back in the day I ran a 'main dealership' suppling Weber, SU and Zenith / Stromberg carb kits and performance packs to both retail and trade customers alike ... we wouldn't have dreamt of passing off mismatched components like this.


All times are GMT +1. The time now is 05:32.

Powered by vBulletin
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.