Heater matrix
 

Hi there

I am contemplating doing a heater matrix change myself, seen a few American YouTube videos and it looks do-able

Can I just ask you all a few questions:

- when the matrix leaks, is it usually into the drivers' or passenger side?
- is it ok to clamp off the rubber tubes on the bulkhead, as I have seen on YouTube? I'm not mechanically competent enough to drain all the coolant down
- when I come to remove the matrix, which side will I need to pull it out from (passenger or drivers?)
- is there a good place to source a new one, or do I just use eBay? OEM is Behr, is that right?

cheers all

- when the matrix leaks, is it usually into the drivers' or passenger side? Don't know

- is it ok to clamp off the rubber tubes on the bulkhead, as I have seen on YouTube? I'm not mechanically competent enough to drain all the coolant down Not recommended as you could damage hoses.

- when I come to remove the matrix, which side will I need to pull it out from (passenger or drivers?) Driver side on RHD car

- is there a good place to source a new one, or do I just use eBay? OEM is Behr, is that right? This one... Click

Remember to order two new O-rings part# 3545586

It's okay to clamp the coolant hoses in the engine bay, saves draining it all down but there will still be water in the matrix so be prepared for this. The matrix is easier to remove from the passenger side, you will need new O rings as mentioned...
Check for any leaks before refitting the carpets etc

Got mine from PFS...
https://www.partsforvolvosonline.com...oducts_id=3634

Just my personal experience-

Mine leaked into the passenger footwell
I did it by clamping the hoses in the engine bay with no ill effects, if you are going to do the matrix draining the system is no more complicated than doing the matrix, just don't be heavy handed with the drain point on the bottom of the radiator, possibly best just to disconnect a hose.
I took mine out from the passenger side (left in a RHD car), the tricky bit is the contortions of reaching into the car, over the doorsill and up under the centre of the dash.
My matrix came from a respected local motor factor, so somewhere you think you can trust would do, the one Volvo again linked to at PFV is listed for £39.60.
As already advised get the rubber O rings for where the pipes go into the matrix, quite often these are a cause of leaks, I got mine from the local Volvo dealership, I can't remember the price but less than a fiver for parts that would definitely fit.

that's all really helpful, thanks everyone. I guess the PFS one is not Behr, but still decent quality.

I'm not sure if your car will have the radio power amplifier wiring plug in the way for doing the job, my 1995 850 did. If so you just have to unplug it to get some more wiggle room to move things about. It was a bit of a pain in the butt to get plug off because of the angles but very doable.

Good luck, Its not as bad of a job as you think it will be.
An old pillow over the door/sill area defo helps with the comfort of getting under the dash :tongwink:

Nissens is the only other make I would fit.

I did mine a few weeks ago. The matrix comes out of the PASSENGER side easiest - on a RHD car. You'll need to remove the radio amplifier if you have one fitted in front of the matrix like I did. I drained the cooling system entirely as I didn't want to clamp the hoses - they're around 25 years old and will have hardened. Its a good time to renew the coolant as well!

I fitted a NISSENS brand matrix - this comes with the 2x o-rings which is nice. I used those as they seemed to be of a decent quality and I haven't had any issues since (tempting fate?!!! :) )

Brief write up about it is here - https://www.volvoforums.org.uk/showp...&postcount=114 although I followed RobertDIY's youtube guide - https://www.youtube.com/watch?v=OdKzDfvOoQA . He offered a good tip about using a bag to catch the coolant in the matrix! Well worth watching IMHO

HTH

Not that bad
 

I've done this job three or four times now, and it really isn't too difficult.

They tend to leak into the left hand passenger footwell.

You take it out on the passenger side.

I clamped the engine bay hoses without any issues, but I do have a proper hose clamp.

Remove the carpets as far as you can. Taking the matrix out results in spillage, which otherwise takes ages to dry out.

Get new Volvo O-rings.

Get a branded matrix. Cheaper ones have fewer channels and don't heat the passenger compartment so well. The ones I've had from PartsforVolvo were fine. The Eurocarparts one was rubbish.

Fit a new thermostat whilst you're at it.

Make sure you put back the little drain hose. You'll see what I mean when you get there!

Hope that helps.

Jack

Not sure if this applies to the OP's 98 car. You can't clamp hoses on a 1999 car, late cars are Aluminium.