Volvo Owners Club Forum - View Single Post

woland · Jan 15th, 2008, 02:57

I bought 940 (jul'95) with b230FT engine, because i have project p1800 and i thought that its better to buy whole working volvo than just engine, tran, etc. So i plan to bring my engine to Poland in volvo 940 case

, make all modification while in 940 and swap to p1800 when done. Car was bought on ebay ( http://cgi.ebay.co.uk/ws/eBayISAPI.d...:X:RTQ:GB:1123 ) and from first seen something was wrong. Somebody drill hole in cup of coolant recovery tank, just near one way valve. When i press pipe, small Whale make me wet

. I used screw to fix it. When car gets hot, pipes are hard, theres no leaks, i dont know why somebody "fix" it. next thing is cut protection wire between shaft of turbo bypas valve and bypass servo. So i plan to buy HPT, but bought Zero presure turbo or even underpresure

. I fix it, now it blow.

Problem is that between 1000 (idle OK) and 3000 rpm engine has no power. To start i have to make more than 3000 rpm and slip chutch for few seconds. On the motorway, there is very narrow range of pedal positions when car works. When i press in minimally deeper, engine choke and loos its power. Its almost impossible to reach 4000 rpm during ride, looks like very poor mixture, i am afraid of valves and pistons overheat. When (on idle) i rapidly press acc, engine reach about 2500, next fall down to 1500 and cycles repeat and repeat. When i make it delicatelly, i can reach 6000 rpm.

I suspected air flow meter, so i went to garage in Kingston. In first place, guys told me they cant connect scanner to this ecu, because operator is sick (!), in second garage serviceman said that have no right plug.

Now i have nice turbo power limiter, with very wide range of usable rpms and multiposition acc pedal... )

Of course i can spend 2xvalue of car for new airflow meter, thottle position sensor, oxygen sensor, knock sensor or pressure reg, but maybe You can tell me where in south London i can find somebody with knowledge, diag and plug in one time? I should be on ferry tomorrow, but i am little affraid of 1000 mile trip.

Thanks for any help.
PS. My mobile is +48606929188 SMS with address of service will be perfect, i have gprs conn only, but i will check this thread frequently.

Simon.

Jan 15th, 2008, 02:57	#1
woland New Member Last Online: Feb 25th, 2008 02:07 Join Date: Jan 2008 Location: Kraków	Help me please! Service needed URENTLY! I bought 940 (jul'95) with b230FT engine, because i have project p1800 and i thought that its better to buy whole working volvo than just engine, tran, etc. So i plan to bring my engine to Poland in volvo 940 case , make all modification while in 940 and swap to p1800 when done. Car was bought on ebay ( http://cgi.ebay.co.uk/ws/eBayISAPI.d...:X:RTQ:GB:1123 ) and from first seen something was wrong. Somebody drill hole in cup of coolant recovery tank, just near one way valve. When i press pipe, small Whale make me wet . I used screw to fix it. When car gets hot, pipes are hard, theres no leaks, i dont know why somebody "fix" it. next thing is cut protection wire between shaft of turbo bypas valve and bypass servo. So i plan to buy HPT, but bought Zero presure turbo or even underpresure . I fix it, now it blow. Problem is that between 1000 (idle OK) and 3000 rpm engine has no power. To start i have to make more than 3000 rpm and slip chutch for few seconds. On the motorway, there is very narrow range of pedal positions when car works. When i press in minimally deeper, engine choke and loos its power. Its almost impossible to reach 4000 rpm during ride, looks like very poor mixture, i am afraid of valves and pistons overheat. When (on idle) i rapidly press acc, engine reach about 2500, next fall down to 1500 and cycles repeat and repeat. When i make it delicatelly, i can reach 6000 rpm. I suspected air flow meter, so i went to garage in Kingston. In first place, guys told me they cant connect scanner to this ecu, because operator is sick (!), in second garage serviceman said that have no right plug. Now i have nice turbo power limiter, with very wide range of usable rpms and multiposition acc pedal... ) Of course i can spend 2xvalue of car for new airflow meter, thottle position sensor, oxygen sensor, knock sensor or pressure reg, but maybe You can tell me where in south London i can find somebody with knowledge, diag and plug in one time? I should be on ferry tomorrow, but i am little affraid of 1000 mile trip. Thanks for any help. PS. My mobile is +48606929188 SMS with address of service will be perfect, i have gprs conn only, but i will check this thread frequently. Simon.