|
700/900 Series General Forum for the Volvo 740, 760, 780, 940, 960 & S/V90 cars |
![]() |
|
1989 740 GLE Injection type?Views : 1817 Replies : 8Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Junior Member
Last Online: May 28th, 2023 08:12
Join Date: Oct 2010
Location: Flitwick
|
![]()
Since getting my 1989 740 GLE last week, I’ve been reading up on the Volvo maintenance hints that’s linked from here.
It looks like a really useful resource, and I’ve used the VIN decoder so I know it’s got a B230E engine (there's red paint on the block, under the grime and cobwebs). But do I have Bosch LH 2.2 or 2.4 injection? And does it matter? The car is running well but I’d like to do a basic service to make sure it’s as healthy as it can be. I plan to get a set of spare injectors then send them off for cleaning, is there a part number I need to look for on ebay, or are they the same as on another car? Have a pic, for your trouble ![]() ![]() |
![]() |
![]() |
![]() |
#2 | |
Senior Member
Last Online: Jun 2nd, 2013 22:00
Join Date: Jun 2010
Location: salford
|
![]() Quote:
Well done on your find, how much did you pay? I don't know how much maintenenace you have done, but unless you haven't already, check your front wheel arches down where the mud guards are, but further in, check for soft metal, rust holes , these areas are prone to rust, and peel your footwell carpets up in the front to check for any dampness, and any rust patches around that area, and the weld seams here too, Depends on how it has been looked after, mine is an ultralow mileage unloved volvo, more pictures please! |
|
![]() |
![]() |
![]() |
#3 | |
Junior Member
Last Online: May 28th, 2023 08:12
Join Date: Oct 2010
Location: Flitwick
|
![]() Quote:
The only maintenance I’ve done so far is to tighten the battery clamp, unblock the washer jets and replace a sidelight bulb. I was thinking of writing to Volvo and complaining about the shoddy workmanship to be honest... |
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Last Online: Jun 2nd, 2013 22:00
Join Date: Jun 2010
Location: salford
|
![]()
Whats the mileage on your car, injectors generally aren't a bother, however the seals on them can perish and let air past them an cause an odd idle and fuel consumption issues, injectors aren't cheap though, i've seen them for £47 each!
Maintenance for this machine, i would treat as if the history is unknown, so i'd check your brake pads, condition of underbody and wheel arches, as per mentioned, i would change coolant and charge with 50/50 mix of clean water and volvo coolant, or one suited for an aluminium block, Change oil and oil filter, semi synthetic 15W/40 is a good all year round oil, Air filter and spark plugs, (bosch super 4's) check ignition wires for cracks or wear, distributor cap, Check flame trap, (crankcase ventilation system) its a small wire mesh that bungs up full of sooty crud and can cause overpressurisation on the crankcase, in turn pushing oil out between gaskets all over the place, Clean throttle body and lubricate the throttle cable and its rotating drum, Lubricate locks and keyholes, and bonnet joints, check the drains in the bottoms of doors are clear of rubbish, and the rain water channels are clear from leaves and debris etc. I'd wash and wax her also even though she does look clean ![]() I don't think it matters about the injection system size, and probably will be the 2.3 LH one.. See how you get on! |
![]() |
![]() |
![]() |
#5 |
VOC Member
|
![]()
The B230E had either K-Jet or LH2.2.
LH2.4 was only fitted to the F/FT/FK variants. A pic of the engine bay would be useful.
__________________
Gavin ![]() 1997 945 CD (B230FK) [RIP: 1991 945 Turbo (B230FT) 1992 945 SE turbo (B200FT)] |
![]() |
![]() |
![]() |
#6 |
Junior Member
Last Online: May 28th, 2023 08:12
Join Date: Oct 2010
Location: Flitwick
|
![]()
Thanks, chaps!
![]() |
![]() |
![]() |
![]() |
#7 |
Senior Member
Last Online: Jun 2nd, 2013 22:00
Join Date: Jun 2010
Location: salford
|
![]()
Hi again, i can confirm that is a K-Jet mechanical injection system, pretty simple and straightforward to work on, though since everything is mechanical, they say k-jet can act a bit odd sometimes even when everything is all in order..
Clean that throttle body and air plate inside the large rubber bellow, it can get dirty with crankcase blowby oil, and will sometimes cause juddery cruise speeds Change you cambelt if there are no signs of it being changed, also if check around the water pump the seals can sometimes leak, but i would change the water pump and all of the belts if you're going to have the timing belt done.. |
![]() |
![]() |
![]() |
#8 |
New Member
Last Online: Dec 22nd, 2010 22:53
Join Date: Sep 2010
Location: Oxford
|
![]()
Hi all,
For those with the K-jetronic this site is a wealth of tips; http://www.diagnostic-assistance.co.uk/mech_inj.htm It's probably already been posted a few times here already! Thanks Jim |
![]() |
![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|