|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
Information |
|
Vida/Dice 2011D isssueViews : 3488 Replies : 26Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Aug 20th, 2013, 15:49 | #1 |
Premier Member
Last Online: Yesterday 22:45
Join Date: Aug 2008
Location: Newcastle
|
Vida/Dice 2011D isssue
I'm reposting this in the 07> forum in the hope that a new audience may be able to help with a Dice issue I have.
When I connect my dice to the car or an external power supply the device registers that no power is being supplied. Vida starts normal, login is normal ,the profile screen is normal but on the diagnostic/details screen in the upper RH corner where there has historically been a "connected" and the battery voltage and key Pos 2 details, what I now have is "disconnected" in an orange box, and the battery and key details are grey with no details. When in the diagnostic programme the power of the dice is intiially shown as 4 dashes "--.--" until its connected to an external power supply, then it reads "0.00" The interface test is a fail - "Self diagnostic connector not attached" from previous help is a normal response- all other tests are a pass. The unit still appears to read the various modules, but there are instances of comm error codes been noted between various components that I know did not exist before. I have tried to update the dice firmware from version 5.6.1 to 5.6.2 but nothing changed. I have read/researched many forums/posts but no one appears to have suffered from this issue My worry is using a faulty unit (if it in deed is) could damge my car. Any assistance/comments gratefully received. Cheers Bob |
Aug 20th, 2013, 19:26 | #2 |
VOC Member
Last Online: Feb 26th, 2016 19:58
Join Date: Aug 2011
Location: Exmouth
|
You shouldn't have to supply additional power to the DICE unit.
So, if you have VIDA running and plug one end of DICE into the laptop and the other into the car - what happens?? My concern at the moment being you've tried a firmware update and you say nothing happened. Is this because there was no lights/power to the dice unit or did it go through the motions but just didn't update or did it throw up an error and fail?? Basically my thoughts are with the fact it sounds like there is a problem with your actual DICE unit. The only other thing to try would be load VIDA onto some other machine and retry your DICE unit on that. |
Aug 21st, 2013, 10:16 | #3 | |
Premier Member
Last Online: Yesterday 22:45
Join Date: Aug 2008
Location: Newcastle
|
Quote:
Para 2) vida running, plug dice into car,firmware and USB lights flash,Vehicle status light flashes red faster than the first two lights. IIRC this is no different to when I had no issues. Para 3) I have learned how to change the firmware at will. Using the diagnostic programme that came with the dice. After each change of firmware, the programme shows which firmware is loaded. However regardless of which firmware is loaded I am unable to see the battery voltage or key pos 2 icons on the diagnostic/details screen in the upper RH corner and rather than the word "connected" what I now have is "disconnected" in an orange box. Para 4) Good call re load on 2nd machine. If I still have this "unconnected" issue it can be assumed the Dice is faulty. But does this make it unsafe to use????? It will still read codes and clears them as normal. All the other tabs ie "Haynes manual" type functions still work, its just it says "Disconnected" on the diagnostic/details function and "reads spurious comms error codes" between some control modules when it reads for DTC's Cheers Bob Cheers Bob |
|
Aug 21st, 2013, 10:48 | #4 |
VOC Member
Last Online: Feb 26th, 2016 19:58
Join Date: Aug 2011
Location: Exmouth
|
Ok, so it is doing almost everything it should just not the showing battery and key position.
All I can say if there is dome fault with the DICE (after checking on 2nd machine) then I myself wouldn't be confident using it. All it could take is a slight glitch when reading modules or clearing codes etc... to perhaps cause some very costly damage. There has been a couple of people who have had problems with their DICE recently - mikealder being one. |
Aug 21st, 2013, 12:41 | #5 |
Member
Last Online: Apr 5th, 2015 19:49
Join Date: Apr 2012
Location: Malvern
|
Check you have 12vdc on pin 16. Some times this is powered from the cig lighter fuse.
|
Aug 21st, 2013, 14:13 | #6 |
Premier Member
Last Online: Yesterday 22:45
Join Date: Aug 2008
Location: Newcastle
|
Yes: have 12V dc at pin 16.
Loaded vida/dice onto 2nd machine and have same issues. You can add my name and Gatos to people who are encountering issues with dice. Thanatos told me in a previous thread that Vida 2011D was time restricted ( he did not elaborate) but both myself and Gatos started having problems after 12 months or so use. Before I call this dice busted does anyone have a copy of Vida 2010 or a little earlier, which I could try and use to see if it is the software or hardware being the trouble. Cheers Bob |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|