|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
![]() |
|
Estate Tow BarViews : 1544 Replies : 19Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#11 |
Master Member
Last Online: Yesterday 15:09
Join Date: Oct 2013
Location: Alberta
|
![]()
Doesn’t the “P2200” on the label indicate it’s for an estate?
|
![]() |
![]() |
The Following User Says Thank You to c1800 For This Useful Post: |
![]() |
#12 |
Premier Member
Last Online: Jun 20th, 2024 07:41
Join Date: Jan 2006
Location: Falmouth
|
![]()
I think it probably does. I forgot that.
__________________
1970 California white 131. |
![]() |
![]() |
![]() |
#13 |
Member
Last Online: Jun 20th, 2024 12:42
Join Date: Jun 2013
Location: Berkshire
|
![]()
Looks like I’ve found my tow bar (hitch) ;-))
|
![]() |
![]() |
The Following User Says Thank You to P1800Ray For This Useful Post: |
![]() |
#14 |
VOC Member
Last Online: Jun 22nd, 2024 14:01
Join Date: Jul 2006
Location: Chatham
|
![]()
FYI: Shows where the bolts go through to the angle iron brace in the spare wheel well Sorry no picture of that but might get round to it.
|
![]() |
![]() |
The Following User Says Thank You to Derek UK For This Useful Post: |
![]() |
#15 |
VOC Member
|
![]()
I think I still have the fitting instructions that came with ours as you could still buy them new, if you get stuck
__________________
1968 Amazon estate (Gracie). 2003 Vauxhall astra estate (her car) 2009 XC90 (Jo) . Not forgetting 1967 Cheltenham Nyala (caravan) |
![]() |
![]() |
The Following User Says Thank You to gillberry For This Useful Post: |
![]() |
#16 |
Trader Volvo in my veins
Last Online: Today 00:22
Join Date: Dec 2004
Location: Anglesey
|
![]() Yes thats the idicator if it is still there |
![]() |
![]() |
![]() |
#17 |
Junior Member
Last Online: Jan 5th, 2024 15:14
Join Date: Nov 2019
Location: Peterborough
|
![]()
Alternatively try towbar manufacturers Watling Towbars in St Albans. They list a towbar for the Amazon and will usually fabricate it if it isn't in stock. It would come with fitting instructions, bolts and a conventional flange type towball fitting.
|
![]() |
![]() |
![]() |
#18 |
Trader Volvo in my veins
Last Online: Today 00:22
Join Date: Dec 2004
Location: Anglesey
|
![]()
The issue with most aftermarket ones is that they go through the bumper
|
![]() |
![]() |
![]() |
#19 |
Member
Last Online: Jun 20th, 2024 12:42
Join Date: Jun 2013
Location: Berkshire
|
![]()
Derek,
Thanks for the photo, I hadn't noticed those holes before. They seem to be full of a caulk and will need cleaning up. How thick should the angle iron be? Surely the side bars must fit to the chassis as well? Gillberry, A photo of the instructions would be nice if you have them. |
![]() |
![]() |
![]() |
#20 |
VOC Member
Last Online: Jun 22nd, 2024 14:01
Join Date: Jul 2006
Location: Chatham
|
![]()
The tow bar side plates fit to the bumper iron attachment bolts. You may have to use longer bolts. Use good quality ones. I doubt if the line of staggered bolt holes is done at the factory. The original instructions may have come with a dimensioned strip for marking them out or you drilled to match the angle iron, I think my interior bar is an angle section, not positive, but that would be better as it is stiffer and stronger. 2" angle about 3/16" thick or about the same thickness as the mating back bar on the tow bar? Can't tell you but if I go up the garage I will check. The spacer washers are about 1/4" thick.
As said, I wasn't fitting it as a first fit. I removed it to fit the stainless rear bumper. It was also a good excuse to paint it. I then refitted it the same as it was. |
![]() |
![]() |
The Following User Says Thank You to Derek UK For This Useful Post: |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|