|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
![]() |
|
DSTC Service Required, then limp mode, then total failureViews : 635 Replies : 7Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
New Member
Last Online: Mar 18th, 2024 17:31
Join Date: Mar 2024
Location: Bloomfield
|
![]()
Hello everyone.
This week, my 2011 S80 had the dreaded DSTC Service Required show up, with the squiggly lines and everything. The car would soon go into limp mode. This happened twice, I pulled over both times, re-started the car and the DSTC was back on (warning off), and drove the rest of the way ok. I took it to the dealer and they told me the battery was corroded and too small for the vehicle -- ok, so maybe not enough voltage. After they overcharged me for that ![]() I guess my only option is to have the steering module replaced (at half the cost with the local mechanic) and hope the dealer was correct? Has anything like this happened to anyone else before? Could it be the steering module to cause this? I have a feeling the module will be replaced and the same issue will return a week later. But, I don't have any more options being that the dealer did a full diagnostic. Thanks so much for even reading this far. ![]() Last edited by gregsl; Mar 12th, 2024 at 20:37. |
![]() |
![]() |
![]() |
#2 | |
Member
Last Online: Yesterday 21:09
Join Date: Feb 2007
Location: Zagreb
|
![]() Quote:
Edited: Oh yes...Did they Reset the BMS (Battery Managament System) when the new battery was installed? Wish you luck.
__________________
[1981...244gld6] - 1992. > 2004. [1997 ... 855tdi] - 2004. > today. [2013 ... V70d3] - 2022. > today. Last edited by hal9000f; Mar 12th, 2024 at 21:53. |
|
![]() |
![]() |
![]() |
#3 | |
New Member
Last Online: Mar 18th, 2024 17:31
Join Date: Mar 2024
Location: Bloomfield
|
![]() Quote:
|
|
![]() |
![]() |
The Following User Says Thank You to gregsl For This Useful Post: |
![]() |
#4 |
New Member
Last Online: May 22nd, 2024 10:30
Join Date: Apr 2024
Location: Abingdon
|
![]()
I've the same symptoms on a 2012 V70 D5. Have you had any luck with getting this fixed?
I get DSTC Service required (No ABS fault illuminated on Dash) with the following codes stored: U041568: Invalid Data recieved from Brake Control Module. U012600: Lost Comunication with Steering Angle Sensor. Then will have have a slight wobble in the speedo followed by the complete engine stop/faluire. Lots of codes stored, including fuel pump to imobiliser. There are no errors logged/stored in the Steering or Brake Control Modules. |
![]() |
![]() |
![]() |
#5 |
Premier Member
Last Online: Yesterday 23:36
Join Date: Mar 2017
Location: Manchester
|
![]()
check for any water ingress around the cem windscreens have been known to become unbonded allowing water onto the electrics
|
![]() |
![]() |
![]() |
#6 |
New Member
Last Online: May 22nd, 2024 10:30
Join Date: Apr 2024
Location: Abingdon
|
![]()
I've conducted the basic can bus check through the OBD socket. 62 ohms 2.4 and 2.6 Volts, happy with the results. It should be 60, and equal to 5 volts combined I believe.
No evidence of water around the CEM or footwell, windscreen was re-sealed ~2019. I did fit a second hand ECU and CEM which were cloned to mine. All was great for about 2 weeks, then the same codes have returned. I do wonder if the car is doing something to the CEM, over voltage? 12.4 at rest, 15 volts at idle across the battery terminals. It currently wont rev to see if it maintains / decreases or increases from 15 volts... Changing back to the original ecu makes no difference. The original CEM has a do not fit sticker on, not sure why? The only thing of note. The clips which retain the 2 main loom ends to the CEM were broken, probably been out before. Couldn't say 100% for certain the CEM is the original or correct one for the car Oliver |
![]() |
![]() |
The Following User Says Thank You to Oliver2012 For This Useful Post: |
![]() |
#7 |
New Member
Last Online: May 22nd, 2024 10:30
Join Date: Apr 2024
Location: Abingdon
|
![]()
I've owned it for ~5 years, its been fine up to know. It is a recent problem which has started.
|
![]() |
![]() |
![]() |
#8 |
Premier Member
Last Online: Yesterday 23:36
Join Date: Mar 2017
Location: Manchester
|
![]()
15 v at idle is quite high the plastic clips on the cem plugs are what hold the plugs in tight try pushing them in as road vibration may have un seated them giving multiple fault codes
|
![]() |
![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|