|
200 Series Articles How to's and Guides for the 200 series. |
Information |
|
How to replace front wishbone bushesViews : 9569 Replies : 5Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 26th, 2007, 22:31 | #1 |
Former contributor
Last Online: May 15th, 2024 09:52
Join Date: Dec 2004
Location: Rhosgoch, Anglesey
|
How to replace front wishbone bushes
Thought this guide to replacing wishbone bushes might be helpful.
I will make the assumption that you know how to remove the wishbones. Removal of the bushes is possible without a hydraulic press if you have a large strong vice. Rear bush - this is held onto the wishbone by a 19mm nut which once undone allows the housing to be pulled off. This can then be placed in a vice to start pushing it out using a couple of sockets as spacers to allow the bush to move - see phote: Once it has moved so the bush is partly out a further large socket (smaller than the bush) is used to drift it fully out: If the outer casing of the bush seperates from the rubber and gets left in it is necessary to find a socket that has exactly the right exterior diameter to be able to push it out - some WD40 mto lubricate can help. Clean the housing ready for the new bush. These bushes are handed so make sure you know which bush is which - the difference is the hardness of the rubber. Support the housing over the vice so that the bush can be placed on top of the hole. It can then be gently tapped into place making sure it goes down squarely. Normally it can be tapped in all the way - it is important to ensure squareness at all times. Front bush - looking at the bush will show which wa it has to be pressed out. Again 3 sockets can be used to start pressing it out: This will not get it completely out but it is easy to drift out with a suitable drift: If the casing is left again this can be pressed out with the right sized socket: Again clean up the housing and start tapping the bush in making sure you are putting it in from the correct side. Once started it is easier to press in using the vice: This will push it partly in, two sockets as spacers are needed to complete the installation. Hope this is useful. Mike
__________________
A Volvo is for life not just for Christmas! Last edited by Mike_Brace; Dec 26th, 2007 at 22:37. |
The Following User Says Thank You to Mike_Brace For This Useful Post: |
Dec 27th, 2007, 10:30 | #2 |
VOC Member
Last Online: Dec 3rd, 2021 08:39
Join Date: Jan 1970
Location: Sutton, near Ely
|
Excellent write up and pictures.
I have always done that big bushing with a copper and hide mallet but using the vice like that looks better. I am surprised that you can get enough force in the vice to do the small bushings, maybe I just need a bigger vice! Andrew |
Dec 27th, 2007, 15:26 | #3 |
Master Member
|
my bro in law batters them out with my sds drill ,i did see somewhere on an american? site a remover using stock gas? fitting pieces which looked interesting perhaps it can be adapted if the sizes vary in bushes.
i had lost the link but a search found it again http://www-ese.fnal.gov/People/wilce...shing_tool.htm whether the parts are available in the sizes mentioned i have no idea but perhaps we have a resident fitter to advise? Last edited by chesters6; Dec 27th, 2007 at 15:38. |
The Following User Says Thank You to chesters6 For This Useful Post: |
Dec 27th, 2007, 16:36 | #4 |
VOC Member
|
many thanks
hi mike ,
an excellent write up ,appreciate it greatly. This is what makes this such a great forum as it gives the DIY maintainer a better sense of confidence when tackling their cars maintenance . Have a very happy and prosperous new year . regards brendan |
Dec 27th, 2007, 17:55 | #5 | |
VOC Member
Last Online: Dec 3rd, 2021 08:39
Join Date: Jan 1970
Location: Sutton, near Ely
|
Quote:
Andrew |
|
Dec 27th, 2007, 20:50 | #6 |
Not an expert but ...
Last Online: Today 07:00
Join Date: Dec 2001
Location: Boncath
|
I did my TA bushes with an angle grinder and a cold chisel, to cut the bush in half and then bend the bits inwards so that they fell out of the lugs. Pulling in the new bush was much easier, with a threaded rod, a collection of washers and spacers, and a distance piece held in with string.
My warning with the front suspension bushes is when unbolting the bracket from the chassis section. Take very great care that you don't strip the thread on the captive nuts when winding the bolts out. I think the projecting ends of the bolts inside the chassis get rusty and pick up debris, and this gets wound into the nut. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|