|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
![]() |
|
Anti skid service requiredViews : 62082 Replies : 132Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#121 | |
New Member
Last Online: May 10th, 2023 10:17
Join Date: Jun 2018
Location: Southampton
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#122 | |
Experienced Member
Last Online: Yesterday 22:27
Join Date: Jun 2007
Location: L/H side
|
![]() Quote:
This is not the familiar BCM Pressure sensor code ..
__________________
|
|
![]() |
![]() |
![]() |
#123 |
New Member
Last Online: May 10th, 2023 10:17
Join Date: Jun 2018
Location: Southampton
|
![]()
Hi thanks for the reply. I don't suppose you have any clue of where to start looking?. Is it a case of starting with the BCM and checking the cabling to the ECM? Any help would be gratefully accepted.
|
![]() |
![]() |
![]() |
#124 |
Experienced Member
Last Online: Yesterday 22:27
Join Date: Jun 2007
Location: L/H side
|
![]()
I would start at the ECU end and look at the plug connectors for signs of water or corrosion . Have you got any ECU fault codes?
__________________
|
![]() |
![]() |
![]() |
#125 |
New Member
Last Online: May 10th, 2023 10:17
Join Date: Jun 2018
Location: Southampton
|
![]()
I did have egr voltage too low and a couple of others all to do with egr this originally lead me to replace the egr. Also in the menu in the car dstc is off and blis reduced function. I have been out in the car today though and no fauilts showing at all.
|
![]() |
![]() |
![]() |
#126 |
Experienced Member
Last Online: Yesterday 22:27
Join Date: Jun 2007
Location: L/H side
|
![]()
DSC off is due to the brake communication fault , were the EGR codes a genuine problem?
__________________
|
![]() |
![]() |
![]() |
#127 |
New Member
Last Online: May 10th, 2023 10:17
Join Date: Jun 2018
Location: Southampton
|
![]()
The way it is looking at the moment I don't think the egr was a problem but it's been replaced so should be OK for a few years now. I will check the ECU at work this week and clean the electrical connections. Typically no fault lights at all on the way into work this morning.
|
![]() |
![]() |
![]() |
#128 | |
Experienced Member
Last Online: Yesterday 22:27
Join Date: Jun 2007
Location: L/H side
|
![]() Quote:
especially under the coolant bottle where it has the AC pipes pressing on it , and there is the edge of the chassis just forward of the coolant bottle ..and on the gearbox side where it can rub on the gearbox.
__________________
|
|
![]() |
![]() |
![]() |
#129 | |
New Member
Last Online: May 10th, 2023 10:17
Join Date: Jun 2018
Location: Southampton
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#130 |
Experienced Member
Last Online: Yesterday 22:27
Join Date: Jun 2007
Location: L/H side
|
![]()
you can do , but highly unlikely to find the fault there , It has dust and waterproof seals on each wire going into the ECU . check your loom as I described above .
__________________
|
![]() |
![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|