|
700/900 Series General Forum for the Volvo 740, 760, 780, 940, 960 & S/V90 cars |
![]() |
|
945 front hub retaining nut re-use?Views : 998 Replies : 17Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#11 | |
Premier Member
Last Online: Today 08:38
Join Date: Jul 2012
Location: Lenzie
|
![]() Quote:
![]()
__________________
V70 D5 SE Geartronic 215bhp Saville Grey 2012MY 940 LPT Manual 1996 740 SE 1990 |
|
![]() |
![]() |
The Following 3 Users Say Thank You to griston64 For This Useful Post: |
![]() |
#12 | |||
Premier Member
Last Online: Yesterday 17:28
Join Date: May 2012
Location: Lakenheath
|
![]() Quote:
Quote:
![]() Quote:
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag ![]() |
|||
![]() |
![]() |
The Following User Says Thank You to Laird Scooby For This Useful Post: |
![]() |
#13 |
🤍💙💗
Last Online: Yesterday 19:22
Join Date: Mar 2006
Location: Lichfield
|
![]()
The later 940 hubs look like they can be regreased. The outer inner race was kinda loose on the new ones I bought, so it's probably possible to take the old hub off, knock that out from the back and add grease.
Should expect a bit of drag, if they could be spun like a catherine wheel then ironically probably be on their last legs. As long as there's no play in any direction then leave well alone. ![]()
__________________
MY97 940 CD LPT Super Sports Edition 2 Turbo, Midnight Purple, 175,000 miles. ![]() |
![]() |
![]() |
The Following User Says Thank You to baggy798 For This Useful Post: |
![]() |
#14 |
Senior Member
Last Online: Today 07:36
Join Date: Jul 2019
Location: Stoke on trent
|
![]()
I too have reused the front wheel bearing nuts .it's put on with a breaker bar so gets maximum tension very tight I kni will replace it when and if wheel bearing needs changing .what that wheel bearing it can fall apart and there's a technique to get it back together!!!
|
![]() |
![]() |
The Following 2 Users Say Thank You to J liddy For This Useful Post: |
![]() |
#15 | |
Premier Member
Last Online: Yesterday 17:28
Join Date: May 2012
Location: Lakenheath
|
![]() Quote:
![]() ![]() There is a very good reason why the hub nut should be torqued to a specific figure and why they should be renewed though.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag ![]() |
|
![]() |
![]() |
![]() |
#16 |
Senior Member
Last Online: Today 07:36
Join Date: Jul 2019
Location: Stoke on trent
|
![]()
I have posted a brief description on how to get back together simple when you know .but only one way to do it from memory
|
![]() |
![]() |
The Following 2 Users Say Thank You to J liddy For This Useful Post: |
![]() |
#17 |
VOC Member
Last Online: Today 15:36
Join Date: Feb 2008
Location: Gloucester
|
![]()
What a contrast. The only wheel bearings I’ve done DIY were the rear ones on my Mk2 Scirocco, same as a Mk1 Golf where the procedure is to tighten to about 7ft lbs and then loosen a bit!
|
![]() |
![]() |
The Following 2 Users Say Thank You to Forrest For This Useful Post: |
![]() |
#18 | |
Premier Member
Last Online: Yesterday 17:28
Join Date: May 2012
Location: Lakenheath
|
![]() Quote:
![]()
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag ![]() |
|
![]() |
![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|