Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 200 Series General > 200 Series Articles
Register Members CarsBlogs Help Calendar Mark Forums Read

Notices

200 Series Articles How to's and Guides for the 200 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

Guide to rustproofing

Views : 7138

Replies : 4

Users Viewing This Thread :  

 
 
Thread Tools Display Modes
Old Jan 29th, 2011, 23:34   #1
Mike_Brace
Former contributor
 

Last Online: Sep 15th, 2018 01:25
Join Date: Dec 2004
Location: Rhosgoch, Anglesey
Default Guide to rustproofing

There has been a lot of discussion about rustproofing 240s. Have just stripped a 240 estate to bare shell I thought I would post some pictures to show the areas that will benefit from waxoyling. I would appreciate any comments and suggestions so we can build up a good guide.

I'll start from the back. One of the very common problem areas on both saloons and estates is where the floorpan meets the rear panel. You can see how they both curve in and are then spot welded together. This makes a good rust trap. This estate is good which is unusual. A good application of waxoyl to the inside of the join is a good idea:



Moving forward another area with a spot welded lip is the wheel arches. From inside a good amount of waxoyl can be applied between the wing and inner arch.

Moving forward to the sills there are access points along the length covered with a plastic plug. This one has less available being a later model so rerar half would be accessed through the seat belt mounting. Also the B pillar can be treated paying special attention to where the hinges are mounted. Also be careful not to block the drain holes in the sills as these drain the water from the air intakes.



This one shows the front part of the sill and the other cpommon rot point which is the A pillar as can be seen here is already rusting:



This one shows the problem with the A pillar better. In front of the A pillar early cars have a vent which provides access to the void that takes the water down from the air intake - another place to waxoyl.



The other obvious areas are the bottoms of the doors (keep drainage holes clear). It is worth ensuring the plastic in the door is intact as this keeps water from damaging the door cards. Also bottom of the tailgate or boot and the leading edge of the bonnet.

Mike
__________________
A Volvo is for life not just for Christmas!


Mike_Brace is offline  
The Following 2 Users Say Thank You to Mike_Brace For This Useful Post:
Old Jan 30th, 2011, 10:08   #2
Paul240480
Ovlovnut
 
Paul240480's Avatar
 

Last Online: Yesterday 23:12
Join Date: May 2006
Location: Nivillac
Default

Another common point is around the rear shock mount area. You may recall my finding these holes in 'Tank' a while back.




If you can get to these early enough (like I did by chance) it will not be too bad. A mechanic inspected mine & found it only to be the inner floorpan. Under the car was solid & is now waxoyled.

As Mike pointed out, that lip at the rear. Mine was apparently quite good!







Repairs, well mine ended up like this, a small plate was spot welded over the biggest hole inside the car. I then sprayed waxoyl down into the cavities. Filled the holes with instant metal & slapped 2 coats of Hammerite on.
Under the bumper, I Kurusted, filled with fibre resin, then put 2 coats of Hammerite on. The area cannot be seen once the bumper is back





It only takes a few minutes to check these points, & those Mike points out. It will be a few minutes very well spent
__________________
1999 V70 T5 SE Auto
2004 V70 2.4SE Auto 'The Welshmobile'
http://www.gitessouthbrittany.com/Car.htm
http://moncopainmonchien.jimdo.com/
Paul240480 is offline  
The Following User Says Thank You to Paul240480 For This Useful Post:
Old Jan 30th, 2011, 13:08   #3
tannachyallen
240SE
 
tannachyallen's Avatar
 

Last Online: May 21st, 2018 20:58
Join Date: May 2007
Location: Strath Brora
Default

Great Mike, the start of another excellent 'How to'.

The mechanic I use gave me some 'Add-It Clear Grease' spray which he uses on exposed surface rust. Areas like trailing arms or suspension members that are meaty bits of metal that just have a corroded surface. It sprays realy thin and then starts to creep and get more viscous, but never fully dries. It has big temperature tollerences and seems to resist being worn off by water etc when driving.
__________________

240 SE Auto 1991
tannachyallen is offline  
Old Jan 31st, 2011, 21:56   #4
chesters6
Master Member
 
chesters6's Avatar
 

Last Online: Oct 17th, 2012 16:14
Join Date: May 2007
Location: Farnham
Default

Damn you more work for the summer ,pointless trying this time of the year the water you dunk the waxoyl can in to get it fluid goes cold to easily.
found a brand new tin at a bootfair yesterday for 2 so i have no excuses to not to
chesters6 is offline  
Old May 31st, 2011, 20:02   #5
Paul240480
Ovlovnut
 
Paul240480's Avatar
 

Last Online: Yesterday 23:12
Join Date: May 2006
Location: Nivillac
Default

Reading this thread: http://www.volvoforums.org.uk/showthread.php?t=125920 prompted me to search for this one that Mike started. It was intended to become a guide with folks adding there findings as and when to provide a mass of information about the dreaded 'tin worm'. One from which we can all benefit.
So here it is 'bumped'. PLEASE do add to it. I'll give it a couple of days and then will ask for it to be added to 'articles' with a link back to this 'original thread' like the others .
Thanks for reading


Link to original thread.
__________________
1999 V70 T5 SE Auto
2004 V70 2.4SE Auto 'The Welshmobile'
http://www.gitessouthbrittany.com/Car.htm
http://moncopainmonchien.jimdo.com/

Last edited by cumbrianmale; Jun 6th, 2011 at 18:24.
Paul240480 is offline  
The Following 3 Users Say Thank You to Paul240480 For This Useful Post:
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 20:32.


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.