|
S80 '98-'06 / S60 '00-'09 / V70 & XC70 '00-'07 General Forum for the P2-platform S60 / V70 / XC70 / S80 models |
![]() |
|
Low power at times and ECM-1507Views : 5519 Replies : 4Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
New Member
Last Online: May 28th, 2018 21:29
Join Date: May 2018
Location: Sofia
|
![]()
Hello Volvo fans
![]() I have been checking a lot of threads related to S60 D5 limp modes, turbo low pressure and error number ECM-1507 in particular, but I do not find anything matching my case. So here is the story - for over a year I own S60 D5244T5 mod. 2008, manual transmission, and I experience a very strange low power behaviour - that happens at times (around 60% of engine starts) and the result is that the car lacks power - it seems that turbo compressor does not work and it behaves like a regular diesel car. The low power "mode" usually happens when:
After checking the error codes with Volvo diagnostics tool, ECM-1507 appeared: -------------------------------------------- 284: ECM-1507 Turbo control. Too low pressure ---- Possible sources
Fault symptoms
-------------------------------------------- So, the journey began... For maintenance I go to a Volvo garage, but it is not the official dealer (I am reluctant to go to the dealer, because of the really poor service it provides - I will not go into the details, it's not my point) - and I really trust those guys, since they are more than VOLVO fans and drivers themselves, they also built a really strong Volvo and Saab community - generally, they are honest guys, doing excellent job and they do it because they want to, not only for the money. So, I checked the error with them (apart from an air conditioning sensor error, ECM-1507 was the only one that appeared) they also checked the system for air leaks (several times on different occasions) - nothing was found. I had the swirl flaps replaced, and I have asked them to clear the EGR-valve - so that was done. I put a lot of hope on the EGR cleaning, because the car has had a really strange behaviour - it could start with the error, I can drive it that way for some time, but if I had to stop and drive again in - let's say 10-15 minutes - when I start it again, there is a very high chance that the limp mode is away and the car has power again. I can drive it, the turbo charger seems to work, no problem for some time - the limp mode can reappear on the very next stop/start or after a couple of starts. So I thought the EGR valve jammed because of working temperature.... But cleaning it did not help for the limp mode problem. As I mentioned above at times the car has power as it should - no problem with low or high RPM/speed, it goes just fine. That's why I hope it is not the turbo charger that is the problem - much more that it had been serviced/cleaned before I bought it. Well, I am wondering if any of you, ladies (I hope we have ladies in the forum too ![]() I would very much appreciate if you can share your experience and thoughts, thank you in advance! Last edited by George Rio; May 13th, 2018 at 20:58. |
![]() |
![]() |
![]() |
#2 |
Member
Last Online: Jun 6th, 2022 19:30
Join Date: Jan 2018
Location: Dover
|
![]()
Try removing the connectors to the turbo control motor and give them a spraying of contact cleaner, when either removing or replacing the connector give the turbo control motor a "technical tap" with a small hammer.
Take the pre cat lambda sensor out and give it a clean with carb cleaner also spray the connections with contact cleaner, take the greatest of care whilst removing the lambda sensor. Clean the contacts on the exhaust gas temperature sensor, the connector is a pain to separate btw. It may well be none of those things but the technical tap may work ![]()
__________________
Do you ever walk into a room then wonder why you're there? Welcome to my world. John. |
![]() |
![]() |
The Following User Says Thank You to drone For This Useful Post: |
![]() |
#3 |
Member
Last Online: Jun 6th, 2022 19:30
Join Date: Jan 2018
Location: Dover
|
![]()
Forgot to say, take the main ecu connectors apart and give them a spray with contact cleaner.
It can't do any harm and it doesn't take much oxidisation to create digital ripples.
__________________
Do you ever walk into a room then wonder why you're there? Welcome to my world. John. |
![]() |
![]() |
The Following User Says Thank You to drone For This Useful Post: |
![]() |
#4 |
New Member
Last Online: May 28th, 2018 21:29
Join Date: May 2018
Location: Sofia
|
![]()
Hi drone - thanks for the idea! I have not noticed any significant oxidisation, but I guess that the not so obvious might be the key. The "technical tap" you suggest makes me think that you would lean towards a further check on the turbo control motor..?
|
![]() |
![]() |
![]() |
#5 |
New Member
Last Online: Jan 10th, 2020 12:44
Join Date: Nov 2015
Location: Kaunas
|
![]()
Hi, how you solved this problem?
|
![]() |
![]() |
![]() |
Tags |
ecm-1507, limp mode, low boost pressure, low pressure |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|