HID Headlight & Sidelight Bulb Question...!

[Dre]

Hi guys,

I'm going to retrofit an HID kit to my S40 at some point, could someone please tell me what an 08 S40 with Projector headlight uses in terms bulb size/fitting is please.

Also, what types of bulbs are in the Sidelight as I would like to possibly put in an LED - or perhaps an LED bar to fill the 'slit' which the sidelight uses.

Finally, the DRL's in the orange lense, what size are they also?

Many thanks - also if someone has filled the sidelight with an LED strip/bar please post a pic as I would like to see this done.

Thanks guys,

Andre

[Dre]

Done a quick search through the threads, can I confirm bulbs are;

H7 - main beam
Sidelight - 501

What is the high beam? - As this isn't part of the projector unit, is this an h11 by anychance? - and here is a random question, what length is the 'slit' where the sidelight bulb goes from top to bottom in terms of inches? could anyone answer that for me please, many thanks.

[SonyVaio]

H7 - Headlight- dipped beam
HB3 - Main Beam
501 sidelight

Put your details in here and you will find all the bulbs you need - LINKY

[fenton_jd]

Careful with these kits.

If you dont earth them seperately from the exisiting wiring loom, the wipers have been known to fail. The exisiting wiring loom shares its earth point with the wiper motor.

You need a kit with CANBUS error cancellors, and to isolate the earth points for both left and right headlamps.

I've fitted a HID kit before, and it blew the alternator regulator fuse after 2 weeks, causing a scary error on the dash "POWER SYSTEM SERVICE URGENT"

I ended up taking the HID's out at the side of the road, on a cold rainy winter evening after work. Quite embarrasing.

[C30 Driver]

You don't need a canbus canncellors or at least I haven't got them on mine and still ok after 241 hours.

[Dre]

3 more questions, then I'll leave everyone to crack on with their weekends!

1) Does anyone know the difference between 501, T10 and W5W in terms of sidelight bulbs?.. The way I understand it is.. 501 is the fitment i,e the Base.. T10 seems to allow for more bulbs so the shape of the bulb itself can have a large amount of Leds in it albeit smds.. and W5W.. seems to be larger again? - Any bulb experts in here that can help me out?..

2) Is the side marker light.. the little one behind the reflector just a 501?

3) What size is the ring around the projector if I was to fit a halo? 90mm?


Cheers guys!

André

[jasonb]

I can answer number 3 easily enough since I wrote up an installation page on the LED Halo's some time back.

If you want to keep the lights intact (ie, do not want to remove the lens cover) then you need 90mm halo's but...make sure the diameter on the outside edge is 90mm not the inner or the centre else, they'll not fit.
I've just ordered the second generation of LED's, I'll let you know how I get on when they arrive.

Should come with two wires to connect in to the side light wiring.

I didn't read the whole thread, which year was your car manufactured or is it a pre or post face-lift model?

I know the other answers, just ping me if you don't get anywhere.

As for sidelights, T10,501,W5W are much the same in all honesty when you're talking about LED's.

Points of note.
It's all about lumens or basically how much light is omitted by the sum of the LED's.
You're right, go for SMD's and pref. 5050 since they're on of the brightest.
I'd go for 1210's next if the numbers stack up.

Avoid replacing the indicator bulbs with LED's, too many challenges and potentially lethal to the health of the CEM.

Good luck with your upgrades!

[SonyVaio]

Have a look at this LINKY it will answer 1 and 2. I've no idea about the size for number 3 but if you do then please post and let us know.

[jasonb]

Q 3
http://www.volvoforums.org.uk/showthread.php?t=117940

[Dre]

Originally Posted by jasonb

I can answer number 3 easily enough since I wrote up an installation page on the LED Halo's some time back.

If you want to keep the lights intact (ie, do not want to remove the lens cover) then you need 90mm halo's but...make sure the diameter on the outside edge is 90mm not the inner or the centre else, they'll not fit.
I've just ordered the second generation of LED's, I'll let you know how I get on when they arrive.

Should come with two wires to connect in to the side light wiring.

I didn't read the whole thread, which year was your car manufactured or is it a pre or post face-lift model?

I know the other answers, just ping me if you don't get anywhere.

As for sidelights, T10,501,W5W are much the same in all honesty when you're talking about LED's.

Points of note.
It's all about lumens or basically how much light is omitted by the sum of the LED's.
You're right, go for SMD's and pref. 5050 since they're on of the brightest.
I'd go for 1210's next if the numbers stack up.

Avoid replacing the indicator bulbs with LED's, too many challenges and potentially lethal to the health of the CEM.

Good luck with your upgrades!

Thanks a lot mate - I'll post up what I've got in store when all the parts arrive, I'm actually busy getting some custom CCFL's made up, as I prefer a solid ring of light as opposed to the individual 'dots' an LED halo produces, I'm also trying to keep all the colours matching on the front so it doesn't look too busy - so currently I'm talking to a company in america to get that sorted out. You'll see what I mean when it's done

I promised my partner I wasn't going to go crazy with this car as this was my sensible car, but after spending 7 years modifying jap cars and it's a hard habit to let go of lol..

The only thing is - I have found bulbs with like 68 smd's in them, but they look to be quite long compared to stock I'm sure one place said they were like 1.75 inces, just hope there is enough room to fit longer/larger bulbs before I do pull it all out to fit bulbs that don't fit, it's easier to ask people that have already done it..

Can you remember how big the channel was for the middle sidelight slit.. p.s. my car is facelift 2008 R-Design