|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
Information |
|
Fitting new A/C beltViews : 4677 Replies : 27Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Feb 11th, 2018, 14:49 | #1 |
Member
|
Fitting new A/C belt
Hi all,
I have to get to grips with fitting a new A/C belt, in addition to the aux belt and the cam belt, 'cos that's what everyone says you should do. Anyway, I was kind of dreading the A/C belt fitting on account of it's a stretch belt that requires no tensioner which makes it a PITA to fit AFAIC. Anyway, done a bit of searching for a service tool that would make the job a lot easier and the Gates site threw up this pictogram (I hate them for their ambiguity!) which seems to imply that a special tool is not needed and one can just use a 3mm cable tie instead! As I said I'm no good with pictograms so if anyone can verify this is the case I'd be most grateful. Here are the diagrams in question which outline the procedure: https://www.gatesautocat.com/pdf/5PK628-620SF-IS.PDF Is that what they're trying to say? |
Feb 11th, 2018, 15:11 | #2 |
VOC Member
Last Online: Today 10:26
Join Date: Feb 2013
Location: North Yorkshire
|
ITs a nice idea but it won’t work. The ac pump has a centre nut but this only spins the clutch not the pulley. The pas pump pulley is held on with 4 10mm bolts if i remember correct. You can’t use these to spin that pulley either as you will shear them no question.
The only way is either the correct tool, or bruit force. It took me an hour of swearing to get it on with my hands. It’s an awkward position especially if your doing it on the floor. When I do it again I’m going to buy the tool or just pay a man to do it.
__________________
Previous -03 S40, 04 V70 D5, 04 V70 D5 Sport, 05 V50, 07 S60 D5, 09 V70 D5 R design, 12 XC60 DrivE, 15 V60 D3 Current- 05 XC90 D5 Exec, 12 XC70 D4 AWD Se Lux, 14 S80 D3 Se Lux Last edited by GrahamBrown1; Feb 11th, 2018 at 15:18. |
Feb 11th, 2018, 15:18 | #3 | |
Member
|
Quote:
|
|
Feb 11th, 2018, 15:23 | #4 |
VOC Member
Last Online: Today 10:26
Join Date: Feb 2013
Location: North Yorkshire
|
I would say your asking for trouble, you don’t want to damage the new belt. When I wound it on with me hands it took a lot of messing about to get it sat in the correct place as it has to go over the lip on the pas pulley. There is a good chance you will split the new belt if you try and spin the engine on starter and it’s not seated right.
Someone might come along with a better way but I couldn’t think of one once I’d chucked all my spanners across the drive.
__________________
Previous -03 S40, 04 V70 D5, 04 V70 D5 Sport, 05 V50, 07 S60 D5, 09 V70 D5 R design, 12 XC60 DrivE, 15 V60 D3 Current- 05 XC90 D5 Exec, 12 XC70 D4 AWD Se Lux, 14 S80 D3 Se Lux |
The Following User Says Thank You to GrahamBrown1 For This Useful Post: |
Feb 11th, 2018, 16:43 | #5 | |
Member
|
Quote:
|
|
Feb 12th, 2018, 13:01 | #6 | |
Senior Member
Last Online: Nov 12th, 2023 19:03
Join Date: Jan 2011
Location: NW
|
Quote:
With a cable-tie attached to the belt, the fitter can't do any more damage [to the belt or the car] than they would by forcing the belt on by hand. Starter motor ? No way, sounds very dangerous. Besides, if you've not got the auxillary belt fitted, if you turn the engine over, there won't be anything turning the upper pulley (aux belt goes on outer pulley, A/C belt on inner pulley)....or have I got that wrong ?
__________________
V70 D5 185 SE Lux P3 (with rear integrated booster seats, which the kids love !!) |
|
Feb 12th, 2018, 13:38 | #7 | |
Member
|
Quote:
There are several vids on YT showing the method; here's one I found: https://www.youtube.com/watch?v=AvdeYR7riZE |
|
Feb 12th, 2018, 22:37 | #8 |
Slow git
Last Online: Apr 11th, 2024 22:09
Join Date: Sep 2009
Location: Gairlochy
|
I want the right tool.....
Reading this thread with interest. Today I ordered an AC stretch belt for my 2011 D3 V70 5 cylinder. Didn't know I needed a tool.
I want to invest in the proper tool but can't find it online. Can someone post a link please?! |
Feb 13th, 2018, 10:19 | #9 | |
Member
|
Quote:
Here you go and let us know how you get on: https://ww2.gates.com/europe/brochur...ation_id=15470 |
|
Feb 13th, 2018, 18:51 | #10 |
Member
|
Well, what a king sized PITA that was. Using a cable tie just seemed to make it even more difficult. The only solution was brute force and ignorance, during which some slight damage was done to the new belt. Much of the problem is that you have to removed the long, serpentine auxiliary belt in order to replace the small A.C belt. When you do that, you make it 100 times harder to turn the pulleys on the small belt, but turn them you must to get the new belt on. Volvo could so easily have incorporated a couple of lugs on the power steering pulley to facilitate that, but they didn't. Not good at all.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|