|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
1961 Volvo PV544 in HollandViews : 86396 Replies : 750Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Nov 19th, 2018, 22:31 | #491 | |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
Quote:
I assume I need string on both sides of the slot for the metal trim?
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
|
Nov 20th, 2018, 10:27 | #492 |
Master Member
Last Online: Jan 24th, 2022 17:08
Join Date: Nov 2008
Location: small village in the north of Germany
|
Only one side
Have a closer look to the chrome. It will fit on the outer edge to the rubber. The inner part isn't fixed. If I remember right there was a thread called "fitting window chrome to 144" Good luck, Kay |
The Following User Says Thank You to mocambique-amazone For This Useful Post: |
Nov 24th, 2018, 16:02 | #493 |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
I've been putting off the trim and thought I might...
...get the front screen in position as well.
Unfortunately I forgot about the dashboard - that the screws that hold it in place close to the windscreen are hard to reach with the screen in place - and then of course I didn't have the wider M6 washers I should have bought by now for the new fixings => Then I remembered the windlace => It is all about getting your ducks lined up isn't it? (And I'm not doing very well with that at the moment!)
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
Nov 29th, 2018, 13:56 | #494 |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
Still struggling along!
Delays and delays again I'm afraid to report.
I did manage to get a little bit of progress done today, however, it was one of those bits that has been sitting about waiting patiently for a bit of attention. I'm calling this bit a "heater director" - not sure what Volvo call it but it directs the warm air from the heater to your feet or to the ducting for the windscreen The flap was removed ages ago (not sure where that is actually so that could be the next delay!) and I vowed to get the main housing in the sand blaster ASAP. That was months ago - still better late than never I guess => ^^^nearly always looks worse then it is => Bit more derusting with the Rustyco and then another quick wazz in the sand blaster and then a quick squirt of epoxy (and see how long that takes to dry) before a top coat.
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
Dec 2nd, 2018, 15:56 | #495 |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
Still avoiding the windscreen trim...
...and the humidity is too high for epoxy paint on the heater director assy
So I had a look at the steering box today. Hmmm - trouble at mill. Fallen at the first hurdle. Putting the steering shaft and worm gear into the casing - meant to protrude by a certain amount (mine pokes out further than the specification in the book - but soldiering on) - then you adjust the shims on the bottom of the steering box to get a prescribed torque. (Note if using new bolts make sure they don't end up in the working area!) I can get close to the required torque but the shaft rotation then feels very notchy - blinking dreadful I'm sure it comes down to this pitting on the shaft => Even though the lower bearing cup looks pretty dreadful => ^^^It runs smoothly in the bearing^^^ The upper bearing cup looks fine ####### So I guess the question is - anyone come up with a solution for a pitted steering shaft before?
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
Dec 2nd, 2018, 16:39 | #496 |
Premier Member
Last Online: Today 17:04
Join Date: Jul 2007
Location: Connecticut, USA
|
Army;
If it was properly together, it must be able to go back that way....you just haven't found what's different and not quite right yet...and if that little pitting is all you have, consider yourself lucky...just weld it up and carefully grind it back down...! Cheers |
Dec 2nd, 2018, 18:52 | #497 |
Master Member
Last Online: Jan 24th, 2022 17:08
Join Date: Nov 2008
Location: small village in the north of Germany
|
No welding at this place please!
You will find a company which is able to weld with a laser ( no joke) and grind it down to the original. Expensive and still the only proper way. The balls of the bearing are gone too. Have a look first if you find a new bearing. Hard to find for bad luck. Good luck Kay |
Dec 2nd, 2018, 19:40 | #498 |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
I don't think I'll be welding it Ron (sorry) - I'm not brave enough to do that. At a push I might try epoxy but I'll look into getting the area repaired - probably have a heart attack at the price...
...the lower bearing cup is seriously expensive best part of 150 euros... ...the ball bearings themselves look standard - I might be able to get them out of the race with out too much agro (we'll see)
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
Dec 2nd, 2018, 19:59 | #499 |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
Loctite 3478 looks like it might do the job - dunno - might be worth a try before I find someone who can do a better job...
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
Dec 3rd, 2018, 18:52 | #500 |
New Member
Last Online: Oct 23rd, 2020 12:39
Join Date: Feb 2013
Location: Isle of Wight
|
Fawn colour.
Hi Army,
I know you've probably decided on body finish now, but here is a link to a PV for sale in Sweden, the same rare colour as yours. http://www.blocket.se/skaraborg/Volv....htm?ca=11&w=3 Love your restoration. It's cheered me up no end. I am on my second PV now, and. despite paying a high price with the assurance it was one of the finest from its North Sweden owner, it has so many issues, that I've taken it all apart and started again. I have replaced quite a few of the windscreen bright metal trims, and know that the reproduction ones aren't a very good fit. I'll send you some pictures. Best regards Tony |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|