Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 850 / S70 & V70 '96-'99 / C70 '97-'05 General > 850/x70 S1 Articles

Notices

850/x70 S1 Articles How to's and step by step guides on a specific repair or modification to a Volvo 850/70 car.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

Inlet Manifold Removal, Oil Seperator And PCV System Change

Views : 20337

Replies : 0

Users Viewing This Thread :  

 
 
Thread Tools Display Modes
Old Nov 3rd, 2007, 15:42   #1
Jod T5
Phoenix from the ashes
 
Jod T5's Avatar
 

Last Online: Mar 19th, 2024 10:13
Join Date: Jan 2006
Location: Finchingfield
Default Inlet Manifold Removal, Oil Seperator And PCV System Change

There has been a fair amount of talk regarding crankcase pressure leading to rear crankcase seal faliure so below is a step by step on manifold removal and breather system change...
Stage 1 Check the following http://www.fcpgroton.com/volvo850oiltrapturbo.htm for part numbers relating to your vehicle (by engine number), i did not bother with any of the volvo clips as i had an assortment of jubilee clips to hand, the volvo clips are a pain in the ass...
the parts i went for are
1 x 1271988...oil trap £16.00
1 x 9471644...hose and assorted guff £21.40
2 x 1389574...elbow (unused) £3.60
1 x 9146266...inlet manifold gasket £6.30
1 x 9135990...throttle gasket (unused) £1.75
total inc vat £57.64
Stage 2 Identify your pcv valve on the inlet air pipe.....

remove the crankcase ventilation pipe (larger one) , the inlet manifold blow off pipe (smaller one) and the electrical plug...
Stage 3 Remove air intake pipe at the turbo, air box and intercooler pipework including the ducting to the throttle housing...(not shown removed) it is also advisable to remove the dizzy cap and the spark plug cover..(also not shown removed)

Stage 4 Release the accelerator cable from the cable drum and the linkage ball joint....remove the drum frame from the throttle housing and put aside...
Then remove the one retaining bolt and remove the presure regulator hose at tree on the throttle body and then the throttle inlet hose can be removed and put aside in the engine bay....

Stage 5 Remove the fuel rail cover and injector wiring and put aside in engine bay. Then remove the fuel rail clamp on the rear of the top of the engine and unscrew the fuel inlet pipe on the left of the injector rail, be prepared for a small fuel loss...the rubber hose may be left intact...
Stage 6 Remove the two 10mm bolts from the injector rail and carefully pull the rail away from the inlet manifold and twist it so it can be rested upside down on the top of the engine. The rail can be left in the manifold if the rubber fuel hose is removed but it is unlikely it will come off without being cut so have some spare

Stage 7 Using a 10mm extension socket with u/j remove the top manifold bolts and loosten the bottom ones several turns..the only real difficulty is the bottom left hand bolt that can only be accessed as shown below which means the top hose must be removed at the thermostat....it is at this stage that the 12mm dipstick to manifold bolt and the underside 12mm bolt need to be removed...note do not waste time and skin using a ratchet on these, invest in a 12mm ratchet closed spanner...and a 10mm one while you are at it..they are priceless tools

Stage 8 Lift manifold up off block and set asside removing the left hand side bleed pipe and the breather pipe from the oil seperator at the cam cover so that the manifold can be withdrawn...

The oil seperator will now be clearly visable...

Stage 9 Remove the plug to the left hand knock sensor and remover the pipes to the pcv and discard..To remove the oil seperator from the block there are two bolts and finally the two hoses to the block are removed by breaking the clamp on the top hose and unscrewing the adjustable clamp on the bottom..
check the condition in particular of the bottom "return" hose for blockage, i shoved a piece of hosepipe in and blew to reasuure myself that the airway was clear...they were..

good pipe bad pipe.............................................. ....... old seperator new seperator

as you will see the pipework is clearly knackered but externally the seperator looks "used" only, however it was very coked inside...
At this stage if you did not before remove the dizzy

so that the new pcv and blow off pipe can be intalled in position..Put on new inlet manifold gasket and replace the dizzy cap

Connect the blow off pipe to the inlet manifold

Stage 10 Repace the inlet manifold and torque to 20nm.....AFTER you have done up the inlet bottom mounting bolt...

Stage 11 Replace the fuel injectors, using the two 10mm bolts, their wiring and the injector rail cover..

Stage 12 Replace the accelerator drum frame and reconnect the accelerator cable and the linkage

Stage 13 Replace the throttle housing and gasket if required, mine only needed a skin of instant gasket... not forgetting the pipe to the pressure regulator, and reconnect the throttle air inlet pipework. Then ensure that all electrical plugs heve been replaced

refit the air inlet hose to the turbo and fit the ventilation pipe and blow off to the pcv, the latter will require a jubilee clip

Stage 14 Replace the airbox, air inlet to airbox and intercooler pipe work....not forgetting the dipstick to inlet manifold bolt

i have omitted serveral small bits and bobs regarding disconnecting this and connecting that which will be all apparent to anyone undertaking this operation...
This job is only imo a 2/5 and is easy provided you are methodical and keep your bolts etc in order...
Do not forget your 12mm ratchet spanner....
__________________
Dum Spiro Spero
VOC 20419

Last edited by Jod T5; Nov 4th, 2007 at 08:08.
Jod T5 is offline  
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 23:24.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.