|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
Information |
|
Intermittent stallingViews : 3737 Replies : 35Users Viewing This Thread : |
|
Thread Tools | Display Modes |
May 2nd, 2018, 13:28 | #1 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
Intermittent stalling
Hi all, having an intermittent issue with my Petrol 2.0 C30 the last couple of weeks, hoping someone can give me some pointers...
I first noticed it when coming up to a roundabout, as I dip the clutch just before coming to a stop the engine just died. It took a bit of effort to get it started again, engine turning over but not starting, and after a few seconds it started and everything was fine for the rest of my journey. A few days later I was on a windy county road, doing a steady 40MPH and noticed the car had become a bit jumpy, and not running nice. I could put my foot down on the accelerator and it would seem hesitant to accelerate, but would eventually go. Then i noticed if I took the car out of gear, feet off all the peddles, and let the revs drop down to idle, it would stall. Again after a bit of effort it would start again. This has happened 5 times in the last 2 weeks, and the rest of the time it's driving nice and as I would expect. Any pointers as to where I should start looking under the bonnet? TIA Edit: I should add, that at no point do I get any error lights on the dash... Last edited by superhifi; May 2nd, 2018 at 13:32. |
May 2nd, 2018, 17:52 | #2 |
Member
Last Online: Feb 5th, 2024 21:38
Join Date: Mar 2018
Location: north
|
throttle body position sensor that has gone bad? Maybe a bad/dirty throttle body. I had similar problems with my 1.8L petrol which is almost the same engine. It was not stalling but almost.
I removed the airbox (torx) and cleaned the throttle body with some carb cleaner and a towel. Might be worth a look. |
The Following User Says Thank You to volvopilot For This Useful Post: |
May 3rd, 2018, 08:56 | #3 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
Thanks, did you remove the throttle body, or clean it in situ? I'm guessing it's easier to clean off the car?
I've kind of assumed that if it was a sensor/electrical issue that the car would detect it and flag up a warning light on the dash. Unless whatever is going on is not 'serious' enough to put a light on? |
May 3rd, 2018, 13:24 | #4 |
Junior Member
Last Online: Apr 1st, 2024 13:28
Join Date: Feb 2018
Location: Carshalton
|
Hi,
Just to add, I found it easier to remove it completely. Disconnect battery and then its's airbox hose clamp to unlock, sensor connection and 4 bolts. Then you can actually unscrew sensor from housing - I did that to avoid any potential contamination with carb cleaner, just in case I went a little bit enthusiastic with spraying. My throttle was really dirty, it took multiple applications of carb cleaner and wiping of dissolved crud. Eventually it all came all nice and shiny. 30 mins. all in. Installation is reverse of removal. Good luck. |
The Following User Says Thank You to FracturedButWhole For This Useful Post: |
May 3rd, 2018, 13:40 | #5 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
Cheers for the pointers, i'll give this a go this evening when I get home from work.
Driving to France on Saturday for a week, so ideally i'd like to nip this in the bud before then! Will keep you updated. J |
May 3rd, 2018, 22:12 | #6 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
Right, so had the throttle body off earlier, given it a good clean with some carb cleaner, and put it all back together. Went for a quick test drive with no issues, but shall see how I get on tomorrow morning on the way to work.
Incidentally, when I had the throttle body off the car, I noticed that in its natural position it isn’t quite closed, and can be pushed fully closed, but then it springs open again. Is this by design? I have a photo, but can’t upload from my phone, I’ll get it uploaded tomorrow morning. |
May 3rd, 2018, 22:43 | #7 |
Junior Member
Last Online: Apr 1st, 2024 13:28
Join Date: Feb 2018
Location: Carshalton
|
Hi there,
Yes, it is by design. It has to let a little bit of air, even in the "closed" position. Cheers |
May 4th, 2018, 10:15 | #8 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
Good to know! All went well on the way to work this morning... FIngers crossed it's done the job!
Out of curiosity, I removed this with the throttle body last night: LINKY googling the part number doesn't really tell me much, but what the heck is it?! |
May 9th, 2018, 07:10 | #9 | |
Member
Last Online: Feb 5th, 2024 21:38
Join Date: Mar 2018
Location: north
|
Quote:
Have you been getting the same problems since cleaning the throttle body? |
|
May 16th, 2018, 12:47 | #10 |
Junior Member
Last Online: Jan 17th, 2022 11:48
Join Date: Feb 2017
Location: Hertfordshire
|
After doing some further digging, I have concluded that it is an 'Oscillation Damper'...
Still having issues with the stalling. Trip to France and back went relativly smoothly, but since I got back it's been acting up usually once a journey. I bit the bullet and bought a DiCE, and this is telling me there's something wrong with the throttle position sensor. I'm going to take the throttle body off tonight and have a proper look at the sensor/poteniometer module... |
The Following User Says Thank You to superhifi For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|