|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
Information |
|
D5 water pump removal/replacementViews : 2586 Replies : 8Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Apr 19th, 2019, 08:27 | #1 |
Member
Last Online: Yesterday 00:22
Join Date: Oct 2018
Location: Hertfordshire
|
D5 water pump removal/replacement
I've searched but failed to find any information concerning how to replace the water pump on the D5 engine. Mine is a D5244T10 205 PS. I've removed all the bolts holding the pump in place, but right now I can't see how the pump is going to come out as the gap is so narrow. I don't want to risk losing the timing by removing the rear timing cover and cam pulley.
If anyone has done this job and can give me some tips I'd be extremely grateful. |
Apr 19th, 2019, 09:14 | #2 | |
Experienced Member
Last Online: Today 16:01
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
The Following 2 Users Say Thank You to Clan For This Useful Post: |
Apr 19th, 2019, 09:54 | #3 |
Member
Last Online: Yesterday 00:22
Join Date: Oct 2018
Location: Hertfordshire
|
Many thanks for your advice. That's very useful. I think I will follow your advice and put it back in place. My only concern is that I might have damaged the gasket when I removed it. If so, I will use the one that came with the new pump, even if it's not as good as the original.
Thanks again. |
Apr 19th, 2019, 13:22 | #4 | |
Experienced Member
Last Online: Today 16:01
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
Apr 19th, 2019, 14:12 | #5 | |
Member
Last Online: Yesterday 00:22
Join Date: Oct 2018
Location: Hertfordshire
|
Quote:
|
|
Apr 19th, 2019, 18:39 | #6 |
Member
Last Online: Yesterday 00:22
Join Date: Oct 2018
Location: Hertfordshire
|
I've worked for the best part of five hours on this, three of which were with a mate. The conclusion is that on this particular engine at least, it's impossible to remove the water pump (with the engine in situ) without taking off the rear timing cover. To remove this cover, the cam pulley must be removed. My concern was losing the timing, as a) the cam might turn when undoing the bolts and b) the holes in the pulley are slotted and the timing depends on it going back in place perfectly. I could possibly have dremelled accurate marks, but I didn't trust myself working on an unlocked cam. On this 205 PS engine, and maybe others, there are fuel supply and return lines that are right in the way of getting the pump out. One other option would have been to cut a piece out of the inner cover, but that would have left a permanent gap. I have to say that the thoughtless engineering that renders this job so difficult is very annoying. Other vehicles have two-piece inner covers, and this arrangement would have allowed the pump to come out. So I have ended up having to put the original pump back, but with an inferior gasket as the original broke up. So I am left worse off than when I started. There's one more problem - part of the inner case has to go behind the pump, so it had to be released to let the pump mate up properly. An example of shoddy engineering from Volvo, in my opinion. They probably couldn't care less - most of the cars will have left the dealer network well before this job might need doing.
|
Apr 21st, 2019, 07:43 | #7 | |
XC70 Owner/VOC Member
Last Online: Apr 8th, 2024 15:07
Join Date: May 2016
Location: Montreal, QC
|
Quote:
|
|
Apr 21st, 2019, 09:57 | #8 |
Junior Member
Last Online: Nov 6th, 2023 16:34
Join Date: Feb 2019
Location: Glenrothes
|
oil
sadly even changing the oil can be an issue if you put a little too much in lol
that said most things are straightforward enough with the exception of tools-ie handbrake retraction,crank locking tool and diagnostic equipment |
Apr 21st, 2019, 10:25 | #9 | |
Member
Last Online: Yesterday 00:22
Join Date: Oct 2018
Location: Hertfordshire
|
Quote:
The kit you mention isn't expensive. My VIDA and DICE cost £50, and I think the crank locking tool (I borrowed one) is about £30. VIDA will do the handbrake retraction, but otherwise a 9V battery will apparently do the trick. My beef is not one of complexity, but of access. Next time I do work on this area I will get myself some locking pins so that I can work on the crank and cam without fear of ruining the timing. |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|