|
850/x70 S1 Articles How to's and step by step guides on a specific repair or modification to a Volvo 850/70 car. |
Information |
|
How to get your car looking great!Views : 15988 Replies : 0Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Feb 20th, 2011, 16:02 | #1 |
VOC Member
Last Online: Aug 31st, 2024 18:41
Join Date: Jan 2011
Location: Montrose
|
How to get your car looking great!
Hi all
After several requests, I have put together a plan for getting the most out of your car's appearance, through a planned valeting programme. It is always best to have a plan in front of you, so you remember what you have to do and in what order, so you can pace yourself and get the work completed on time. To do the whole of the plan below, I standardly take 10 to 12 hours to complete, but the programme can be done in sections. HOW TO GET YOUR CAR LOOKING GREAT AND KEEPING IT THAT WAY. Whenever possible, start with the interior, so you are not crouching in water from washing the car, while trying to get under the seats, or in the foot wells. Vacuum first: • Use a domestic vac, at least – the 12V car vacuums are not powerful enough. • If your seats are height adjustable, jack them right up to full height for access. • Remove all mats and any other items that are sitting around in the car – CD’s, pens, parking tickets, jackets etc, so the car is totally clear of unnecessaries. • Starting in the front, slide the seats back as far as they can go, so you have full access to the area below and plenty of room to access the foot wells. • Using a firm, clean brush (upholstery brush), start gently sweeping the foot well areas to lift all imbedded grit and vacuum away with the open nozzle. Do not rub the nozzle vigorously over the carpet, especially with a metal attachment, as it will cause wear to the carpet fibres and eventually detract from the appearance of the carpet. • Once you have finished with the front area, slide the seats as far forward as possible, to give good access to the rear for the car. Do the same here, as with the front and make sure the space underneath the front seats is cleaned out properly (this is usually where you will find some coins lying around!). If there is anything sitting under the rails on the floor, get a piece for card, fold it over and push it under the rail, from the outside, forcing the coin, or old parking ticket, etc into the floor space, to be retrieved and spent/binned. • Once the rear wells have been vacuumed, lift the base of the rear seat up and clean under there too. You will be amazed at how much junk is lying under there! Usually crisps and sticky sweets, if you have kids. • Any marks that cannot be shifted with the vac, will require shampooing. This also applies to the upholstery. Use automotive upholstery cleaner and follow the manufacturer’s instructions. I personally use Autoglym Hi-foam upholstery shampoo. Spray the effected area, gently work in with a clean upholstery brush, wipe over with a clean microfiber cloth and leave to dry. • Next, you will need a long crevice tool. The tiny things that you get with a vac nowadays are not much use, so invest in one that can be bought on the .net. I have two flexible tools, one is a foot long and the other is two feet long, so you can get in pretty much anywhere. Run the crevice tool along the outside edge of both front seat runners, to collect any debris and then move to the inside, next to the centre console, where every thing seems to get trapped. When everything is cleaned out of this space, give it a final wipe with a clean microfiber cloth, sprayed with a citrus based cleaner(I use Flash All-in-one, lemon). Next, do the same to the plastic trim around the seats and doors, finishing with a wipe over the seat runners, to brighten them up. • Vacuum the seats, making sure that you tilt the front ones back and clean in the area between the base and the seat back. If the seats are leather, they can either be wiped down with a damp microfiber cloth, after vacuuming, or treated to cleaner and conditioner, depending on their appearance. • Remember to clean the rear shelf, if it is a saloon. Estates can be done at the same time as the boot space. Also return your seats to the correct position. • Use the same processes for cleaning out the boot – and vac parcel shelf. Dusting • Firstly, get another clean, dry microfiber cloth and wipe down all the surface areas, starting with the door cards, and surrounding trim and then on to the dash and the console between the seats, where the bulk of all crumbs and stickiness seems to land. If the plastics are particularly dirty, these can also be cleaned with the citrus cleaner, which eats through the grime and also leaves a pleasant, fresh smell. • Fix a soft bristled attachment to your vac hose, or use a new, unused ½” (6mm) paintbrush, with the metal ferrule covered in PVC tape (avoids scratching) and start to remove all the dust and crumbs from all the joints, gaps and controls in the same method as cleaning the carpets. The paint brush is very good at getting into little spaces, such as around the wiper and indicator stalks, the edges of the instrument cluster and the vents. This process can also be used along the tops of the door cards, between the card and the glass. This is also a good time to vac out the door pockets and wipe out any sticky stuff, with the citrus cleaner. Take your duster, drop the steering wheel down as far as it goes and wipe over the cowling, to remove any hidden debris. Take the cloth by two opposing corners (one in each hand) and place between the steering wheel and cowling, using a to and fro motion, clean all the hidden dust out – you don’t normally notice it, but it really shows up in a photograph! • At this point, you may want to polish the inside of the glass, either with a spray on class cleaning solution or a glass polish. Drop the windows about an inch (2.5cm), apply the chosen solution to the inside of the glass, again with a clean microfiber cloth and then buff off with another microfiber. Clean the top of the outside of the glass at the same time, as it saves you having to drop the windows again, later. Put the windows back to fully closed position and wipe the small section that was hides earlier, with the cleaning solution and then buff dry. • You do need quite a few microfiber cloths, to do this right, but for the interior of the car, you can but a pack of 6 from Asda, for a couple of pounds and they will last you for ages. The only things to watch are that you remove the labels, as they can scratch your paint (believe it or not), don’t wash them with fabric conditioner and don’t tumble try them, as both these actions cause the cloths to loose their “magnetic” dust collecting properties. Just wash them with washing machine detergent and let them hang up to dry. I use three different colours – blue for glass, yellow for applying product and red for removing/buffing. Wheels • Now that the inside is done, we can look at the exterior of the car. It is better to clean the wheels before washing the bodywork, to avoid splashing dirt back on to the car, after it has been cleaned. • Fill a bucket with warm water with some bodywork shampoo – I use a separate bucket for wheel cleaning. • Hose off all loose dirt and debris, with a strong jet from a hose. This will also clean off a large amount of the brake dust from inside the wheel. • Apply wheel cleaning solution to one wheel and leave to soak for about one minute. • Use a small piece of cellulose sponge, soaked in the water, to remove the main dirt from the wheel face and rim, rinsing the sponge frequently. Take a clean toothbrush (also bought from Asda – smart price 3 for about 30p) soaked in the water and work it into all the tight to reach areas, like around the wheel nuts, valve stem and any edges. Rinse off well with a hose. • Repeat on the other wheels. Engine • Care must be taken, not to damage sensitive electrical components under the bonnet, so I shy away from pressure washers, in favour of a slow flowing garden hose. Put a carrier bag over the alternator, to help keep the water out. • Remove any leaves and loose debris from the scuttle and around the engine bay, before doing anything else. • Spray the engine and surrounding trim with an engine cleaner / degreaser. I use Autoglym engine and machine cleaner and work the solution into all areas with a 2” (5cm) paint brush, with taped ferrule. You can also spray the underside of the bonnet and clean in the same manner as the engine bay. • Rinse with clean water, from hose or watering can and check for any greasy spots that have been missed. Re-treat if necessary. • Pay particular attention to things like the dipstick handle that are usually brightly coloured, these days and highlight oily finger marks! • Remove the plastic bag from the alternator and start the engine, letting it run for a few minutes and then switch it off. • Dry the plastic trim off with either a microfiber cloth or absorbent paper workshop towels (best price also Asda, at £2 and can be wrung out and reused – like “Plenty” kitchen towel, but even stronger!). I have seen someone use a leaf blower to dry the engine, but I think it would just kick up too much dust. • Apply a plastic protectant/enhancer to all the trim pieces within the engine bay and buff to a shine with another microfiber. For this, I use either Autoglym vinyl & rubber care, or Armor All protectant, but there are plenty others on the market. • If you drop a microfiber cloth on the ground, either throw it away, or rinse it out and put it in the wash, but do not use it until it is clean. Cleaning the bodywork (my favourite part) using the two bucket method • Rinse over the whole car with the garden hose, to remove all the loose dust and debris from the bodywork, to avoid any scratching. Make sure you blast out all the mud from under the wheel arches, before washing the car and rinse off the tyres. • Never use sponges or brushes to clean your car, as brushes can scratch the paintwork, even with soft bristles and sponges can trap the grit in the outer surface of the sponge, in effect, turning it into a piece of sandpaper. It is best to use either sheepskin or noodle wash mitts, as there is no chance of dropping it on the ground. The sheepskin & noodles draw the grit up into the mitt, keeping it away from the surface of the car, reducing the risk of scratching. • Mix up a spray bottle of water and car shampoo, roughly 6:1 mix. Spray over the whole car and leave for a few minutes, to soak into the bodywork, while you get the buckets ready. At the same time, apply some insect remover to the front of the car, to assist in the removal of the carcases from the paint. • For anyone not familiar with the two bucket method, two buckets are used to reduce the risk of scratching the painted panels, by keeping the grit separate from the soapy water. Fill one bucket with warm water (not hot, as this strips off waxes) and bodywork shampoo, (I use Autoglym bodywork conditioning shampoo). ¾ fill the other bucket with tepid, clean water, for rinsing. The process is: Soak your wash mitt in the soapy water and wash one panel of the car, starting at the top, where it is less dirty. When the panel is clean, dunk the dirty mitt into the clean water and agitate with your other hand, to remove the grit. Wring it out again, so the mitt can absorb more soapy water from the other bucket and continue as before, until all the panels above the bumper line are clean. • For the lower part of the car, I would suggest using another mitt and only use it on this part of the car, as most of the grit is found here. • Open each of the doors and wash the metalwork in the aperture and also the inner edges of the doors too, still using the two bucket method. Do the same for the bonnet and boot, cleaning all the guttering and internal metalwork. Rinse with clean water from a hose, or watering can, with the rose removed. Rinse the rest of the car with clean water. • Clean out the hinges sections of the doors with a cloth and some citrus cleaner, but don’t remove the grease from the hinges, or any other moving parts, it is there for a reason! • Run your fingers over the lower bodywork and you will probably feel small bumps on the paintwork. These are tar spots and are nearly impossible to remove with car shampoo. Best solution is to apply a tar spot remover solution, such as Autoglym Intensive Tar Remover. Apply some to a microfiber pad of cloth and gently rub onto the affected areas. This will remove all traces of the tar spotting. You may need to quickly wash over the treated areas again, to remove any surplus product. Rinse the car again. • Dry the whole vehicle with microfiber towels, or better still, soft terry, or waffle weave car drying towels. Standard bath or dish towels will most certainly add to the scratching or marring of your paintwork, which shows up as holograms, or spider webs, especially when the sun shines on them. Remember to dry the inside of the door openings and inside of the doors, as well as the inside of the boot, bonnet and places like the grille and openings in the front bumper. Claying the paintwork • Now the car is dry, gently rub your fingers over each panel around the car, checking for rough spots. This will usually feel like fine sandpaper and is caused by contaminants, such as brake dust, airborne pollution and such like. These contaminants imbed themselves in the clearcoat layer of the paint, or on older cars, the paint itself. This can be remedied with the use of a clay bar. The claying process also removes any old wax and polish that has been applied to the car, so retreatment is a necessity. • Most clay kits come with the bar and a spray bottle of lubricant and sometimes with a microfiber cloth. • A clay bar can be cut in half and one piece is kneaded in the palm of the hand, to make soft and then flattened out into a pancake shape. If you drop it, throw it away and get another piece. • One panel at a time, spray the lubricant on to the paintwork and with the clay in the flat of your hand, gently start to move it over the surface of the car. Do not turn the bar over, stick to one side, which will soon be apparent. If the bar starts to grab at the paint, apply some more lube and continue. • When the bar looks very dirty, simply fold it over, with the dirty side facing inward, push it flat and continue as before. When the panel is finished, it should feel as smooth as glass. Buff the panel with a microfiber cloth, remembering to remove the label first. If you fold the cloth in half and then in half again, in the other direction, you have 8 clean sides to use from one cloth. Change to a clean side frequently and yet again, if dropped, use another one. When all the rough sections have been removed, this stage is complete. Polishing – manually • Manual polishing can take some time, to do it right, but the effects can be stunning, to say the least. • If there are any flat spots on the paintwork, this can be due to marring on the clearcoat or paint. This can be removed/reduced, using a cutting compound, if it is more apparent or a polish, if it is a minor blemish. It is not recommended to cut your paintwork too many times, as the compound removes a thin layer of the clearcoat (lacquer), each time it is used, effectively thinning down the protective layer over the paint finish. • For manual polishing, I use Autoglym Super Resin Polish, which is an all in one – paint cleaner, polish and sealer (3 stages in one) and is highly effective, at a decent price. • Start with one panel and apply a small amount of polish to a microfiber cloth, or applicator pad and apply to the paintwork, rubbing in a circular motion. Keep topping up the cloth and rubbing into the paint until the panel is completely covered in a light covering of polish, which will haze over within a few minutes. Buff this off with another clean microfiber cloth (remember to fold it over and use all the available sides). There should be a high level of gloss on the polished panel now. Repeat for all other panel around the car, taking care not to touch and unpainted plastic trim or window rubbers, as it can be extremely difficult to remove again. Autoglym Fast Glass spray is very good at cleaning away polishing marks, as well as for cleaning glass! • You can stop there, or further protect the paint with a gloss enhancer, For dark colours, use AG Ultra Deep Shine and for light colours, AG Extra Gloss Protection. Application is the same process as with the Super Resin Polish, except the whole car is treated at once, left for an hour, before buffing off. Waxing – manually • Most people will stop at the enhancer polish, but for a really high gloss finish, you can apply a coat of wax. With wax, you really get what you pay for, but I really do not see the point of spending £1000.00 on a tub of wax, that may only stay on your car for a few weeks. I use Autoglym High Definition wax, as it can be applied really easily, even in direct sunlight and buffs off with ease, leaving an amazing sheen on the paint. Glass polishing • The clay bar can also be used on the glass, as it helps clear traffic film and other contaminants, using the same process as for the paintwork. • Glass polish can also be applied to the windscreens and windows, to bring up a good shine. Same process as per polishing the car bodywork. • If the glass has been polished recently, a glass cleaner solution may be used instead of the polish Trim detailing • Once polishing is complete, the trim will require treatment. There are many different products on the market, but the ones I use are Autoglym Rubber and Vinyl Treatment, or Armor All protectant, but there is an amazing product from G-Techniq, called C4, which can revive and protect all unpainted external plastics for up to 2 years. It is quite expensive, at £24.00 for a 15ml bottle, but as it lasts for up to 2 years, you really don’t have to worry about it for a long time. • Apply your treatment to all the rubber window surrounds, door handles, mirror trim, door and bumper trim and of course the plastic panel below the windscreen. • If there are still some yellow stains on your alloys, from long term brake dust attack that was not removed with the wheel cleaner apply some metal polish, like Autosol, or Autoglym Metal Polish, to the affected area, with a cotton cloth and buff off – it should all be gone! Spray some alloy wheel sealer onto a cloth and work in to the entire wheel face. This protects the wheels from further brake dust damage and makes the wheels easier to clean next time. • Finish the tyres with a dressing, applied with a sponge. Sometimes, two coats are required as the tyre absorbs the first, leaving the tyre looking dull. I never use tyre paint, as it has the tendency to crack and flake and can also be flicked on to the paintwork, if driven away, before it is totally dry, spoiling all of your hard work. Between main washes, like the above programme, the paintwork can be kept up to standard by applying a quick detailer spray and buffing off again. It only takes about 20 minutes to do the whole car and reinforces the protection of the polishes. That is pretty much it. Your car is clean and protected and will be so much easier to keep clean, as the paint is slick and smooth. A quick rinse is normally enough to get the worst of the dirt off of the car, without any rubbing. I have not written anything on machine polishing, as anyone who is using one, will know what they are doing already. As this is the first instructional document I have ever written on this process, I may have either missed something out, or have not made myself clear enough. If you have any questions on anything in this “how to”, or indeed anything regarding cleaning your car, please feel free to ask and I will do all I can to answer them correctly. If anyone would like me to send them a "Word" version of the document, just PM me with your e-mail address and I will forward it on to you. Thanks for taking the time to read it and I hope is of use to many people. GaryS40
__________________
Current car: 2002 V70 2.4T SE Mod's so far: Orpheus alloys, 10.1" android multimedia head unit, Nappa leather rebuilt, wood trimmed m/function steering wheel, Polestar blue and black calipers, Pipe Dynamics custom turbo back stainless steel exhaust, with 200 cell sports cat, R engine and injector rail covers, tinted rear windows. Previous cars: 1982 760 GLE saloon 1989 740 GLE estate 1991 440 S 2003 S40 S - Gone but not forgotten. ☹ 16 non Volvos. |
The Following 72 Users Say Thank You to GaryS40 For This Useful Post: | achapski, akirkpatrick, Axionknight, Bandwagon, Berkhan, BIGH66, BlAdEAnGeL, bugman, C70Carnut, charlesboya, chelle_belle, christheancient, Colmac, Conradcyclo, DevonMarc, DickyB V70R, dinky1, djsc70, El Padrino, ewanc0, fwoofy, galloot633, greg850, J0hnny, Jabbslad, Jack Spaniel, Jamac, JamesV70R, Jas16, JCT5R, john493, johnjp, kitejumper, MikeS100, mixa, Muscas, nirgunapa, noel pen, notnoRmal, notwhoiam, OldBlueVolvo, panddhicks, patrick264, Paul240480, quantum, ra96099, RaelG, redscotti, ricc, Richard Volvo T5R, Rick Barton, Rob.D, RoscoMac, s70vamp, SafetyJunkie, scr8pdo, silvicontact, smarkc, smokedmackerel, Smudger73, starfighter1, stevegas, sy1, The Hooded Claw, timsmith2, Toplights, trscarr, ukfactotum, v70cd, viv, Waterfieldplace, Yogivair |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|