|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
Steering box leak 544Views : 1182 Replies : 13Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Mar 13th, 2019, 18:17 | #1 |
Senior Member
Last Online: Dec 30th, 2022 02:42
Join Date: Jun 2015
Location: Mesa, Arizona
|
Steering box leak 544
I have developed a steering box leak that is dripping on the ground. Before I tear into it are there easy ways to replace seals without full removal of the box and column?
__________________
1962 Volvo PV544 1951 Studebaker Starlight State Commander Coupe 1953 Studebaker Starlight Commander |
Mar 13th, 2019, 19:41 | #2 | |
marches on his stomach
Last Online: Feb 11th, 2022 03:15
Join Date: Jan 2018
Location: Somewhere in the Netherlands
|
Quote:
Trying to replace seals with it in-situ would be in my opinion a pain in the arse - I think the job will go more quickly with the unit out of the car. If you decide to remove it I'd look very carefully at the item before removal to work out which bit is indeed leaking. Looking at my steering box the most likely source seems to me to be the lower pack of shims at the end of the column - which is why I reassembled my steering box with a load of sprayed on Hylomar on each side of each shim
__________________
1961 Volvo PV544 the quick and easy in between project(!) 1981 Mercedes 300D <=> 230 diesel to petrol conversion project 1965 Series 2a Station Wagon mega build 1992 Mercedes 190E The car that works! |
|
Mar 13th, 2019, 20:01 | #3 |
Senior Member
Last Online: Dec 30th, 2022 02:42
Join Date: Jun 2015
Location: Mesa, Arizona
|
It is leaking out of the lower part of the steering box. Its leaking out of the shaft then it runs along the Pitman arm and then leaks off of the Tie end rod.
__________________
1962 Volvo PV544 1951 Studebaker Starlight State Commander Coupe 1953 Studebaker Starlight Commander |
Mar 13th, 2019, 20:22 | #4 |
arcturus
Last Online: Today 08:12
Join Date: Mar 2006
Location: Sagres Portugal
|
Bite the bullet and do the job once and for all.There might be an alternative. recently on this forum there was some discussion re a steering box grease.
__________________
life's too short to drink bad wine |
Mar 13th, 2019, 20:36 | #5 |
VOC Member
Last Online: Apr 21st, 2024 14:54
Join Date: Jul 2006
Location: Chatham
|
Remove Pitman arm noting the punch marks on the shaft and arm. They have to match up. Pick out the seal and replace. For you perhaps obtain from Mike Dudek or Eric-Planetman. Will it stop the leak? Probably. Will it last? Possibly. It will depend on how much wear there is in the bottom steering box bush and the amount of movement to the shaft it allows. A lot of movement will damage the seal quite quickly depending on the wear.
If you want to go further there is a refurb kit that provides new bushes and gaskets. Bushes need to be reamed to fit the shaft. New shafts with steering worm, which is part of the shaft are no longer available. Finding a better used box is your only other option. Oil spec for the box is 80, the rear axle is 90. Use 90 for both. Do not use grease in the box. There are some thicker fluid greases that may feature in replies to this. The idea is that they reduce the leakage and that may be true. 160 that old Jaguars use for instance. Use at your own risk. It is very hard to get this out of the box if you decide it doesn't work. Bearing grease virtually impossible without a strip down. |
Mar 13th, 2019, 21:00 | #6 |
Senior Member
Last Online: Dec 30th, 2022 02:42
Join Date: Jun 2015
Location: Mesa, Arizona
|
My Studebakers use cornhead grease in the boxes. Nasty, sticky stuff. I will look into replacing the bottom seal. This was my replacement box from a parts car. My original was seized and damaged. I am correct that the entire column has to come out with it? That is how I replaced it.
__________________
1962 Volvo PV544 1951 Studebaker Starlight State Commander Coupe 1953 Studebaker Starlight Commander |
Mar 13th, 2019, 21:54 | #7 |
VOC Member
Last Online: Apr 21st, 2024 14:54
Join Date: Jul 2006
Location: Chatham
|
From what I have seen the column does indeed have to come out.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|