|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
Rear Brake Drums - removalViews : 6305 Replies : 25Users Viewing This Thread : |
|
Thread Tools | Display Modes |
May 29th, 2012, 13:25 | #11 |
New Member
Last Online: Mar 27th, 2019 11:55
Join Date: May 2012
Location: Bagshot
|
Thanks guys for the tips. The puller I have means its difficult to wedge anything in the studs as the puller is bolted on using them, I will try the wood wedge to drum and see how I get on. or maybe its fallen off over night due to the pressure. (Ishouldbesolucky)
|
May 30th, 2012, 01:08 | #12 |
Premier Member
Last Online: Today 13:32
Join Date: Jul 2007
Location: Connecticut, USA
|
Gibo;
...it wouldn't be the first time that after it was put under some serious tension and left overnight, that a little thermal action popped it off...as a last resort you could help this along by putting the assembly under tension, then heating the drum-hub with a propane or acetylene powered flame (I would use the term torch here, but I know torch means something completely different for you). Cheers |
May 30th, 2012, 12:47 | #13 |
VOC Member
Last Online: Today 14:29
Join Date: Jul 2006
Location: Chatham
|
If you're not having any success with the Brookhouse or proper Volvo puller you could try the following method.
With the centre screw slackened off, fit the the puller on the hub. Do up the wheel nuts finger tight and and then undo each one, 1 complete turn. Screw in the centre screw until it's tight. You can use a spanner here to make sure it's under tension. Using a suitable spanner or socket with extension bar (not a ratchet) tighten up each wheel nut up 1 flat a time, going back and forth diagonally across the nuts. This creates a small amount of "wriggle" on the taper which sometimes works when a straight push using the centre screw doesn't. Unless it comes off straight away, patience is always needed but working the puller normally and this alternate method should do the trick eventually. Some Volvo factory pullers have a short T bar for hammering on but mine just has a pair of large nuts locked together. I think they are original and have been on all the ones that have passed through my hands. As mentioned in an earlier post. My estate failed it's "needed when purchased" MOT for having no braking on one of the rears drums. Handbrake OK. Attempts to remove the drum with a factory puller failed and the MOT garage were asked to do the job. They did so but what garage/blacksmiths techniques were used I don't know although they too had the proper Volvo tool. Sod's Law that a few weeks ago, my new MOT a year later showed the rear brake not fitted with a new cylinder was giving the same problems but did manage to get its act together with some agressive pumping. I watched while the tester did this. Got a tcket with an explanation of what was going on, but I'll have to get this drum off to put in the new cylinder bought to go with the other one. Unfortunately the 1st garage onle changed the dodgy one. Time will tell how I get on with this drum. It could well be stuck the same as the first. A question for someone who has both the Brookhouse and the Volvo pullers. Does the Brookhouse one have the same fine thread as the Volvo one? A fine thread multiplies the torque/pressure more than a coarse one. Angular degrees of turn with a fine thread are greater than with the coarse thread to give the same amount of push. Effectively this is the same as using a much longer lever. |
May 30th, 2012, 12:58 | #14 |
New Member
Last Online: Mar 27th, 2019 11:55
Join Date: May 2012
Location: Bagshot
|
Thanks everyone for your comments!!
Well it turns out I am so lucky, bought a big rubber hammer and extension bar and went back to it, after hitting it a few times I thought I better check its not backed off to the castle nut, so I undid the puller and realised I had put the thick washer back on when I spun the castle nut around and the drum was snug against it. Removed the nut and washer and then the drum pulled off by hand. (bit dissapointed I did not get a huge bang as it let go). Anyway new seals in and cleaned up, putting it back together I broke the little clip that holds the shoes to the back plate with the little pin, anyone know if these are easy to source or a suitable replacement?? Top Tip: Reverse the castle nut to protect the shaft but leave out the washer so you get a visible movement when the drum pops off |
May 30th, 2012, 13:45 | #15 |
Master Member
Last Online: Nov 29th, 2020 00:42
Join Date: Feb 2010
Location: Newton Abbot
|
You can get the kits for holding the brakeshoes to the backplate from Brookhouse, Halfords used to do them but last time i asked they were no longer available, more profit in polish and pressure washers i assume.
|
May 30th, 2012, 13:49 | #16 |
Amazoniste
|
However the small spring steel anti-rattle clip (between the top return spring and the wheel cylinder) is no longer available, so keep hold of it!
__________________
Paul - 1967 Amazon 222S B20 o/d Estate & 1961 A-H Sprite Mk2 948cc WANTED - For '67 Amazon estate - offside rear quarter, preferably new old stock. |
May 30th, 2012, 13:55 | #17 |
New Member
Last Online: Mar 27th, 2019 11:55
Join Date: May 2012
Location: Bagshot
|
Are the retaining clips just Volvo PV/Amazon parts or also on later cars.
Really wanted to get one today, but will call Brookhouse if no joy |
May 30th, 2012, 16:07 | #18 |
VOC member
Last Online: Today 10:03
Join Date: Jan 2008
Location: Sheffield
|
The retaining clips are quite common and not peculiar to Amazon.My sons 1999 Corsa has them.
Chris. |
May 30th, 2012, 17:08 | #19 |
New Member
Last Online: Mar 27th, 2019 11:55
Join Date: May 2012
Location: Bagshot
|
Excellent Thankyou, off to Camberley Auto Factors - Must admit CAF are pretty good, the old guy in there identified an unknown ball joint on my GT40 rep by sight as a 72 Granada and was spot on, been in the trade a while!!
|
May 30th, 2012, 17:10 | #20 |
Master Member
Last Online: Nov 29th, 2020 00:42
Join Date: Feb 2010
Location: Newton Abbot
|
You have to watch the length of the shoe retaining pins, i got hold of some generic ones and they were too short.
editted , i meant too long and didnt hold the shoe to the backplate, its all this sun honest. Last edited by Tail; May 30th, 2012 at 17:12. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|