|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
B18 Alternator positionViews : 3098 Replies : 28Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Mar 26th, 2024, 12:25 | #1 |
New Member
Last Online: May 17th, 2024 10:58
Join Date: Mar 2022
Location: Seaton
|
B18 Alternator position
Having blown the B18 engine in my 142 I have a fully rebuilt B18 from an Amazon to replace it. However I have discovered that the lugs which are cast into the block near the timing cover to which the lower alternator bracket attaches are not there. I understand that earlier Amazons had the dynamo on the left of the engine near the exhaust manifold. This would be an undesirable location for an alternator so I presume this was the reason to switch to the right of the engine. Is there a kit/modification available so that I can fit the alternator in the usual 140 position on the right? Many thanks
|
Mar 26th, 2024, 14:33 | #2 |
Premier Member
Last Online: Today 11:56
Join Date: Jul 2007
Location: Connecticut, USA
|
RC;
"...dynamo on the left of the engine near the exhaust manifold. This would be an undesirable location for an alternator so I presume this was the reason to switch to the right of the engine..." ...this location is no less desirable than the Dynamo/Generator location of the earlier cars...in fact, even the early RHD cars also had their Dynamo located on the Manifold side, so there must have been room (maybe it was just "tight")... but this begs the question: How was there room for the Dynamo, but not the Alt on RHD cars (which I cannot answer...maybe OD of a Dyn is less than OD of an Alt...someone with a RHD Amazon can chime in with some pix). I thought a major reason that the Alt was moved to the Distrib side was to clear the Steering Box on RHD chassis, but this was clearly not absolutely necessary...I accept the minor advantage of cooling. If you are going to use the B18 and must locate the Alt on the Distrib side, you will need a custom support bracket fabricated (I expect this might be involved and expensive)...but given the above with respect to there being adequate room on the Manifold side, an alternate solution would be to fit one of the retrofitted Alt brackets available (which add the Alt pivot to a similar location as shown below), onto the three OE Dynamo bracket holes. This might be a simpler, less costly solution than having the custom bracketry designed and fabricated for the Distrib side. ...hope that helps... Source: https://www.sw-em.com/altkit_additio...n_B18_and_B20s Good Hunting! |
The Following User Says Thank You to Ron Kwas For This Useful Post: |
Mar 26th, 2024, 15:55 | #3 |
New Member
Last Online: May 17th, 2024 10:58
Join Date: Mar 2022
Location: Seaton
|
Hi, Thanks, I'me beginning to think I may have to go with the alternator on the manifold side, I believe I have heard of a kit being available to mount on the distributor side but having no success in finding one.
The alternator has a greater OD than a dynamo and also I believe that alternators are more likely to be damaged by heat soak than dynamos but I have no experience either way. |
Mar 26th, 2024, 17:29 | #4 |
Master Member
Last Online: May 21st, 2024 14:52
Join Date: Apr 2012
Location: Droitwich
|
Alternator
There is room for an alternator in place of the dynamo, a Lucas one fits a treat
(the wires aren't as close to the exhaust as they look in the photo). You can modify the existing bracket or use spacers and a suitable length bolt. I've had one in a similar position on a Triumph for years without any problems. There was a kit for the other side of the engine which uses a bracket that uses 3 of the timing cover bolts. Last edited by old fart; Mar 26th, 2024 at 17:32. |
Mar 26th, 2024, 17:47 | #5 | |
Senior Member
Last Online: Today 21:08
Join Date: Sep 2021
Location: MILTON KEYNES
|
Quote:
|
|
Mar 27th, 2024, 11:22 | #6 |
New Member
Last Online: May 17th, 2024 10:58
Join Date: Mar 2022
Location: Seaton
|
Hi, Thanks, I don't particularly want to get another alternator but from your photo I see that there is plenty of room to clear the steering box for my existing one. Trouble is engine and car are currently in different places and it is difficult to assess how things will fit!
|
Mar 27th, 2024, 11:26 | #7 | |
New Member
Last Online: May 17th, 2024 10:58
Join Date: Mar 2022
Location: Seaton
|
Quote:
|
|
Mar 27th, 2024, 15:09 | #8 |
Senior Member
Last Online: Today 21:08
Join Date: Sep 2021
Location: MILTON KEYNES
|
If you converted to electrical fuel pump I’m sure the two 5/16 bolts would be strong enough to hold an alternator, the bracket would have to be a fuel pump delete blanking plate and alternator bracket
|
Mar 27th, 2024, 20:58 | #9 |
New Member
Last Online: May 17th, 2024 10:58
Join Date: Mar 2022
Location: Seaton
|
I have electric fuel pumps and a blanking plate where the fuel pump was, I had thought of running a bracket from there but I think it would be easier off the timing cover bolts.
|
Mar 28th, 2024, 10:09 | #10 |
Member
Last Online: Jun 19th, 2024 13:42
Join Date: Feb 2020
Location: Wales
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|