|
S80 '98-'06 / S60 '00-'09 / V70 & XC70 '00-'07 General Forum for the P2-platform S60 / V70 / XC70 / S80 models |
Information |
|
new to me s60 faults bcm-0111 info pleaseViews : 3451 Replies : 9Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Aug 21st, 2013, 20:14 | #1 |
Junior Member
Last Online: Aug 17th, 2021 18:41
Join Date: Nov 2012
Location: sheffield
|
new to me s60 faults bcm-0111 info please
i got a 265000 mile s60 d5 se my05 and have a few problems here are the codes I've read
bcm-a031 bcm-0111 bcm-a032 engine ecm-6805 ecm2505 ecm-2501 ecm-2502 ecm-5000 any help greatly appreciated cheers russ |
Aug 22nd, 2013, 00:09 | #2 | |
Premier Member
Last Online: Apr 20th, 2024 19:38
Join Date: Dec 2002
Location: Renfrewshire
|
Quote:
BCM:-http://www.volvopartsconnect.com/pages/index.cfm?action=viewPage&siteid=215102&pageid=110 17 'ECM 6805, BOOST PRESSURE CONTROL FAULT' Fault code ECM-2502 Fuel pressure to high Fault code ECM-2501 Fuel pressure to high ECM-2505 Fuel Pressure - Too low pressure ecm 5000 diagnostics says rpm sensor
__________________
Tek-Emo Villis Emo Bis V70 SE NAV 1.6 D2 2015MY POWERSHIFT, D4162T, 93000miles, RED. /VOL FCR/PEPER OBD2/Acron 9135 OBD2/L.E.D Flasher/VDASH/ANCEL BA301/Topdon Top Scan |
|
Aug 22nd, 2013, 13:01 | #3 |
Lord B on T5D5.org
Last Online: Apr 12th, 2024 19:13
Join Date: Nov 2006
Location: rochester
|
loads of info on the 8605 code on the 163 engines
|
Aug 22nd, 2013, 14:36 | #4 |
Premier Member
Last Online: Apr 20th, 2024 19:38
Join Date: Dec 2002
Location: Renfrewshire
|
__________________
Tek-Emo Villis Emo Bis V70 SE NAV 1.6 D2 2015MY POWERSHIFT, D4162T, 93000miles, RED. /VOL FCR/PEPER OBD2/Acron 9135 OBD2/L.E.D Flasher/VDASH/ANCEL BA301/Topdon Top Scan |
Aug 22nd, 2013, 15:32 | #5 |
Lord B on T5D5.org
Last Online: Apr 12th, 2024 19:13
Join Date: Nov 2006
Location: rochester
|
you need to clear the codes, go for a drive and see what re-appears, if you read with VIDA it will tell you how often each code is being triggered, often 1 fault will cause numerous codes
|
Aug 22nd, 2013, 21:30 | #6 | |
VOC Member
Last Online: Feb 26th, 2016 19:58
Join Date: Aug 2011
Location: Exmouth
|
Here is some info from VIDA with regards to your BCM codes.
BCM-0111 Communication between control modules. AYC stability control active for too long Diagnostic trouble code (DTC) information BCM-0111 Note! The diagnostic trouble code (DTC) applies only to cars with dynamic stability and traction control (DSTC). At each new ignition cycle, the brake control module (BCM) compares a value for the steering wheel angle from the steering wheel angle sensor with a calculated value. The diagnostic trouble code (DTC) is stored if the brake control module (BCM) registers that the deviation is too great. The diagnostic trouble code (DTC) can be diagnosed at speeds above 10 km/h and when the steering wheel has been turned 10 degrees in either direction. BCM-A031 Diagnostic trouble code (DTC) information After the steering wheel angle sensor has been initialized, a check of the plausibility of the steering wheel angle is run. The diagnostic trouble code (DTC) is stored if the check is not approved and speed exceeds 50 km/h. The plausibility check can be completed even if BCM-A031 is stored, but before the ignition has been switched off. Diagnostic trouble code (DTC) BCM-0111 is also stored if the check is not completed within one minute. The diagnostic trouble code (DTC) can be diagnosed at speeds above 50 km/h. Substitute value Active yaw control is blocked. Possible source The plausibility check of the steering wheel angle is not approved. Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module. Quote:
Diagnostic trouble code (DTC) information BCM-A032 Condition The diagnostic trouble code (DTC) is stored in the subsequent operating cycle (ignition off and ignition on) if the brake control module (BCM) performs an extended start up check of the DSTC system due to a number of different faults during the previous operating cycle. Possible source The diagnostic trouble code (DTC) has been stored in the previous operating cycle. Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module. |
|
Aug 28th, 2013, 21:05 | #7 |
Junior Member
Last Online: Aug 17th, 2021 18:41
Join Date: Nov 2012
Location: sheffield
|
is the bcm number specific or are they the same on the rest of the range
many thanks russ |
Aug 21st, 2019, 18:49 | #8 | |
New Member
Last Online: Aug 21st, 2019 19:33
Join Date: Mar 2014
Location: Suburban Washington DC
|
Quote:
|
|
Aug 21st, 2019, 19:12 | #9 |
Premier Member
Last Online: Dec 26th, 2021 13:42
Join Date: Dec 2013
Location: Crewe
|
OP hasn't been on for 5 years.
__________________
2002 S60 SE D5 Manual 209000 miles |
Aug 21st, 2019, 19:33 | #10 |
New Member
Last Online: Aug 21st, 2019 19:33
Join Date: Mar 2014
Location: Suburban Washington DC
|
OK, just came upon this thread by searching those codes.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|