|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
Gearbox rebuildViews : 2417 Replies : 14Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Sep 21st, 2021, 20:31 | #1 |
New Member
Last Online: Oct 16th, 2021 20:59
Join Date: Sep 2021
Location: Spa
|
Gearbox rebuild
Is there any tricks to put back the lower and upper shafts in the M40 gearbox?
I found the way to disassemble it but cannot put them back in the box. Thank you in advance |
Sep 22nd, 2021, 10:27 | #2 |
Member
Last Online: Apr 21st, 2024 15:32
Join Date: May 2019
Location: Herts
|
I notice there are a few Videos on tube about rebuilds for these M40 boxes if that helps.
|
The Following User Says Thank You to powen1 For This Useful Post: |
Sep 22nd, 2021, 12:02 | #3 |
1800necwinner
Last Online: Yesterday 16:38
Join Date: Oct 2008
Location: East Anglia ,Suffolk , uk
|
Follow the dismantle process and do it in reverse to reassemble 😎👍
__________________
I grew up on classic volvos hence my passion for them born and breed into the lifestyle ! |
The Following 2 Users Say Thank You to 123GT-AMAZON For This Useful Post: |
Sep 22nd, 2021, 20:51 | #4 |
New Member
Last Online: Oct 16th, 2021 20:59
Join Date: Sep 2021
Location: Spa
|
Hello, I tried to put them back in place with the disassemble process inverted but I can't put the lower shaft in place once the upper one is installed! It seems that the upper shaft takes too much place and I can't place lower axle through the lower shaft and through the holes in the gearbox. Then I tried to place the lower shaft first and then the upper one, same result! Any ideas? Thank you
|
Sep 23rd, 2021, 13:09 | #5 |
VOC Member
Last Online: Apr 21st, 2024 14:54
Join Date: Jul 2006
Location: Chatham
|
Look on David Bello's videos on YouTube or read through this. There are tricks with holding the shafts in with string and using thick grease for the needle bearings. http://vclassics.com/archive/tranreb.htm
|
The Following 2 Users Say Thank You to Derek UK For This Useful Post: |
Sep 25th, 2021, 02:28 | #6 |
Senior Member
Last Online: Apr 20th, 2024 19:21
Join Date: Mar 2014
Location: New Hampshire USA
|
This is a “M40/41 Transmission Rebuild 101” question…
Correct procedure described in factory manuals, Haynes, etc, etc. You need a wooden dowel of identical diameter (~3/4”) to the layshaft gear cluster center rod, just long enough to fit inside the cluster without protruding. This will allow the needle bearings to remain in place during installation. Lay the cluster with it’s shortened dowel shaft and bearings in the bottom of the case and completely assemble the mainshaft cluster above it. Turn the case upside down allowing the layshaft cluster to engage the mainshaft cluster and use the steel layshaft rod to drive out and ultimately replace the wooden dowel. Nothing tricky here, just good clean fun. Good luck.
__________________
'62 Amazon Black/Red 4Dr 65K miles '92 MBz 300CE 2Dr '94 MBz 320TE 5Dr '86 BMW 635Csi '88 BMW M6 |
The Following User Says Thank You to northNH For This Useful Post: |
Oct 13th, 2021, 19:29 | #7 |
New Member
Last Online: Oct 16th, 2021 20:59
Join Date: Sep 2021
Location: Spa
|
Hello, I just want to say that it's quite easy to transform a M40 gearbox to M41 with overdrive! I just did it on mine and the major problem was the oil level to be changed because instead of 0,75L of oil you need 1,6 liter. If any body interested I can tell you how to do it and with pictures!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|