|
S80 '98-'06 / S60 '00-'09 / V70 & XC70 '00-'07 General Forum for the P2-platform S60 / V70 / XC70 / S80 models |
Information |
|
clouds of blue smoke after the overun on accelerationViews : 962 Replies : 10Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jul 5th, 2020, 17:53 | #1 |
Premier Member
Last Online: Apr 24th, 2024 16:40
Join Date: Aug 2008
Location: Newcastle
|
clouds of blue smoke after the overun on acceleration
Hi guys Trying to get to the bottom of this issue as above. The only time I notice smoke is after a length of time with the engine on overun at say 35/40mph then when I accelerate, plumes of blue smoke can be seen in the rear view mirror.
My thoughts are 1) Valve stem oil seals... classic culprit for these symptoms - but in recent years you don't read that much about their failure...and I have no smoke on start up when the oil would have had chance to seep past the seals overnight. All I have is just steam as you'd expect. 2) PCV system clogged.... I have started to strip down the engine, but I'm stuck at the LHS lower inlet manifold bolt - its covered by another part which needs another part removed to gain access. So I'm having 5 minutes think and have decided to seek advice/comments on my situation. As an aside the glove test on the oil filler cap is a loss.... It gets SUCKED down into the filler - good job theres a mesh screen or it would disappear. 3) Some type of turbo/seal failure....There is a little oil on the surface flange of the over the engine top intercooler pipe, but no signs of oil having been in the pipe - but would there be?? I'm wanting to get this repaired but would prefer to choose the right culprit - Cars a 2004 V70 AWD R 120K miles. As ever all comments/suggestions welcome. ( Wife said i should plug the computer in - as it cost all that money -trouble is I don't know what questions to ask it.) Cheers Bob. |
Jul 5th, 2020, 18:50 | #2 |
Flaccid Member
Last Online: Apr 15th, 2024 16:09
Join Date: Nov 2016
Location: Norwich
|
do a compression test see if its worn rings
__________________
2001 Volvo S60 T5 SE 2.3 Geartronic (Scrapped) 2007 Volvo S60 T5 SE 2.4 Geartronic (Sold) 2008 Volvo V70 D5 SE Sport Geartronic (Current) |
The Following User Says Thank You to barrybritcher For This Useful Post: |
Jul 6th, 2020, 13:55 | #3 |
Premier Member
Last Online: Apr 24th, 2024 16:40
Join Date: Aug 2008
Location: Newcastle
|
Time grandad please.....
So... I thought I could at least attempt one of the three options I'd considered as a repair for the Blue smoke the car was blowing out the exhaust.....WRONG!
Despite a brill Utube vid :- https://www.youtube.com/watch?v=oEOzIoVxO4s I have hit a stone wall x2. 1) The LH lower inlet manifold is unaccessible to any of my sockets/spanners - even my 1/4" set. Even if I get this removed and all the other bolts loosened there is a banjo bolt on the LH side of the manifold that sits directly above the alternator and I can't get a spanner onto it and suspect the bolt will hit the alternator before the banjo is removed...( didn't have an issue on the vid.) however,I can forsee a situation where I remove something and can't get it replaced or smash something trying too hard to remove it, and have the car stuck on the drive, so discretion etc. etc. to the fore, I'm giving up..... I'll get everything back together, and live with the slightly higher oil consumption and smoke trail... I'm thus now trying to convince myself ( and justify quitting) that as I have a vacuum in the PCV system, (at least on the glove test) this is not where the fault lies. I have already 80% convinced myself that the problem is not valve seals, ( does the R even have valve seals??) so that just leaves the turbo ( or piston rings) ..and if I apply the above logic long enough and often enough I'll convince myself the smoke is actually a figment of my imagination!! Cheers Bob. currently Pig Sick!! |
Jul 6th, 2020, 15:39 | #4 |
Junior Member
Last Online: Jun 4th, 2021 12:24
Join Date: Oct 2017
Location: Weinfelden
|
Hi Bob,
did your car have extended oil consumption? I wouldn't give it attention, if the consumption is normal. |
Jul 6th, 2020, 16:01 | #5 | |
Premier Member
Last Online: Apr 24th, 2024 16:40
Join Date: Aug 2008
Location: Newcastle
|
Compression test = all cylinders between 170- 180psi needle a bit jumpy, so happy with that. Adding a bit oil, did not change readings strangely.
Quote:
(This AWD R and a 240K miler 2002V70 T5) Cheers Bob - |
|
Jul 6th, 2020, 20:36 | #6 |
Lazy Member
Last Online: Yesterday 20:10
Join Date: Mar 2007
Location: HORLEY
|
Hi.
I watched that U-tube vid. too before i did my T5`s breather system. Yeah, it is a very good guide but i will ad my two-penny-worth. He should have removed the electric fan - 2 bolts and a couple of cable clips. Remove the throttle body and I/C pipes to give hand access under the manifold with an 8mm combination spanner or 5/16" AF ( whichever gives the best fit) onto that awkward bolt you mention. The manifold hole there is slotted so the bolt only needs slackening half-a-turn. He should have undone the brass fitting at the right-hand end and swung the free manifold up to the left. That would give access to the Banjo fitting above the alternator. The small tube from the middle of the Banjo will be brittle and blocked/broken -(guaranteed) . I cut mine away and replaced with some silicon tubing. Trace this breather tube down towards the turbo and check the 2 N/R Valves are functioning properly, and the valve into to inlet duct is clear too. |
Jul 6th, 2020, 21:41 | #7 | |||
Premier Member
Last Online: Apr 24th, 2024 16:40
Join Date: Aug 2008
Location: Newcastle
|
Quote:
Did you have positive crankcase pressure before you did your T5 breather system. I don't appear to have. Quote:
Quote:
Cheers Bob |
|||
Jul 7th, 2020, 08:59 | #8 |
Lazy Member
Last Online: Yesterday 20:10
Join Date: Mar 2007
Location: HORLEY
|
Hi.
I am wrong about the 8mm bolt size. I`m trying to remember as it was a while ago and i`m prone to the odd "Senior Moment" every now and then. All i remember is to have a good selection of slim bodied combination spanners because the amount of turn that you can get on that bolt is minimal. There was no crankcase pressure on my car. The PCV sytem is a service item so i changed mine to avoid all the horror stories about blocked systems. The real culprit is the return drain from the box back to the sump. That is the first area to clog-up .You wont know `til everything is removed. There may be the start of a blockage. The best thing is to blow down the hole using a length of hose and listen for a gurgling noise in the sump oil. You can hear that if you remove the oil filler cap. What i will say is, the engine breathes much better for having done this job. It runs much smoother. There was a build up of oil above the turbo on mine too, although mine didn`t smoke, and i`ve just repaired the turbo. The hot-side sealing ring was worn. Both these jobs seem to have cured it. |
Jul 7th, 2020, 15:55 | #9 |
Flaccid Member
Last Online: Apr 15th, 2024 16:09
Join Date: Nov 2016
Location: Norwich
|
you can move the steering pump quite easily, to go in from the left instead
__________________
2001 Volvo S60 T5 SE 2.3 Geartronic (Scrapped) 2007 Volvo S60 T5 SE 2.4 Geartronic (Sold) 2008 Volvo V70 D5 SE Sport Geartronic (Current) |
Jul 8th, 2020, 09:19 | #10 |
Premier Member
Last Online: Apr 24th, 2024 16:40
Join Date: Aug 2008
Location: Newcastle
|
All apart...
Well... after a lot of cussing, skinned knuckles, and counting to 20 ( 10 was too short) I have finally got everything stripped down- only to find everything is like a new pin!! - almost. I've had the car for 12 years & 70K miles with fully synth. annual oil changes so perhaps I should not be surprised how clean everything is.. My home made vacuum water gauge test was telling me a similar story too.
The LH side manifold bolt was defeated using a 1/4" long extension wobble bar +10mm socket as was the LH side oil can retaining bolt. The video shows its location, but Vida only show the obvious RH bolt!! Now I need to order seals and gaskets for the reinstall.. and that's going to be another big ask. I can see the power steering pump, and alternator having to come out to reinstall that banjo into the manifold.... Cheers Bob |
The Following User Says Thank You to 100K+ For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|