|
300/66 Series General Forum for the Volvo 340, 360 and 66 cars |
Information |
|
360GLT Power SteeringViews : 3849 Replies : 12Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Nov 1st, 2019, 22:32 | #1 |
New Member
Last Online: Nov 11th, 2019 10:25
Join Date: Nov 2019
Location: Ramsgate
|
360GLT Power Steering
I have a 1983 360GLT but find the steering a bit too heavy for an old man! I bought a power steering rack and pump from a later car but I need a three-belt crankshaft pulley to drive the beast apparently. I tried one from a 240 but it doesn't fit the crankshaft...
Does anyone have clue about the variants of pulley in use? My garage tells me that the existing pulley(two-belt) fixes with three bolts and/or a centre bolt and that there may be a three-belt version? Any advice appreciated. This is the second GLT I have owned, the first back in the 90's that was a D reg I think. |
Nov 2nd, 2019, 07:09 | #2 |
Go redblock or go home
Last Online: Today 01:01
Join Date: Feb 2012
Location: UK
|
You will need a different UJ, track rod ends and track rod arms all of which are no longer available.
Have you tried running the tyre pressures slightly higher? |
Nov 2nd, 2019, 15:54 | #3 |
New Member
Last Online: Nov 11th, 2019 10:25
Join Date: Nov 2019
Location: Ramsgate
|
360 GLT PS conversion
Thanks for that...I have all the steering parts including those that you mention...but the correct pulley to drive the pump seems elusive. Increased tyre pressure helps, but if I can have proper power steering it will make the old girl so much more driveable.
|
The Following User Says Thank You to tallboy123 For This Useful Post: |
Nov 2nd, 2019, 20:46 | #4 |
Go redblock or go home
Last Online: Today 01:01
Join Date: Feb 2012
Location: UK
|
I will see if my brother will send me a photo of the pulley on his 360 as it has power steering.
|
Nov 3rd, 2019, 22:14 | #5 |
New Member
Last Online: Nov 11th, 2019 10:25
Join Date: Nov 2019
Location: Ramsgate
|
That's very kind of you! Thanks.
|
Nov 4th, 2019, 07:51 | #6 |
Go redblock or go home
Last Online: Today 01:01
Join Date: Feb 2012
Location: UK
|
That's alright, I have asked him and he said he would... still waiting so I have just reminded him.
|
Nov 4th, 2019, 12:21 | #7 |
300 Maniac
|
Which model 240 did you try the crank pulley from? Your early 360 GLT will be fitted with a B19E engine, it could be that the 3 belt crank pulley you tried from a 240 was from a B200/230 series engined car and the crank is different.
I suspect you'll want to source a 3 belt crank pulley from a 240 equipped with a B21/23 engine and PAS - assuming they exist? There are some aftermarket sources producing aftermarket lightweight crank pulleys if you're not able to source a good used example, for example here: https://shop.klracing.se/sv/artiklar...-8v-3spar.html Would be worth dropping them an email to check it will fit a 360, the only potential issue I could forsee is if the pulley is deeper than the original as there's less clearance between the pulley and radiator surround panel in a 360. Last edited by SteveP; Nov 4th, 2019 at 12:27. |
Nov 9th, 2019, 20:27 | #8 |
New Member
Last Online: Nov 11th, 2019 10:25
Join Date: Nov 2019
Location: Ramsgate
|
It's taken me a while to study what you have said and look into it, and I do think that you are spot on correct about the engine type. I see a pulley on eBay said to be for a 240/740 that is a three-belt and looks to be the correct fitting but I'll check with my garage man before buying because they're asking £55 just for the for carriage from California and I don't want to get it wrong. Meanwhile, I'll follow your link and see what happens!
Thank you so much for your time and effort. Much appreciated. Terry |
The Following User Says Thank You to tallboy123 For This Useful Post: |
Nov 9th, 2019, 20:29 | #9 | |
Experienced Member
Last Online: Today 00:05
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
The Following User Says Thank You to Clan For This Useful Post: |
Nov 9th, 2019, 20:34 | #10 |
New Member
Last Online: Nov 11th, 2019 10:25
Join Date: Nov 2019
Location: Ramsgate
|
360 GLT PS conversion
I'll add to my reply having looked at the site you directed me to: the critical measurement is lining up the belts; so that this lightweight job would have to be the same front to back as a standard pulley; but, as you say, easy enough to contact them to find out! This is exciting stuff!
|
The Following User Says Thank You to tallboy123 For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|