Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > S80 '06> / V70 '07> / XC70 '07> General > S80 S2/V70/XC70 S3 Articles
Register Members CarsBlogs Help Calendar Mark Forums Read

Notices

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

Retro Fitting 2014 Rear Tail Lights

Views : 479

Replies : 0

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Jul 17th, 2017, 22:32   #1
CTCNetwork
Forum Support Team
 
CTCNetwork's Avatar
 

Join Date: Dec 2004
Location: Notts, UK
Default Retro Fitting 2014 Rear Tail Lights

Hi,

As discussed Here over on Swedespeed. Unfortunately, due to the vagaries of photophuckit, many of the informative photos are no longer available! So here are mine!

I fancied this myself... The lights are not as cheap as in the Us but a healthy discount from my friendly parts man made it less painful!

So, how easy is it? Not difficult at all!. I also want to activate the passenger side rear fog light so I was expecting to need to order a "continental part as I had to with the V90. Not at all. There are only 2 parts for the S80, Left and Right (when looked at from the rear of the vehicle - I'll follow that terminology through the topic)!

So, parts ordered and collected following sightings of some rare moths when my wallet was opened!





Ok... Doesn't look too much trouble. The units are held in position by three nuts attached to fixed bolts within the unit itself, but they are fiddly to get to (at least one - on top very much so) and either a long socked or ratchet driver (10mm nuts) is needed to loosen, then remove using finger-tip control.
Unclip the single, central, wire connector whilst also keeping your hand holding the cluster in position (stops it dropping) and then carefully remove straight out and place carefully away (I ended up popping the old ones in the new ones' boxes).





I then cleaned the rear area where the new cluster fits.
[Warning] This is not quite the case for the right side, there is an additional "clip" on the top rear of the cluster to stop it from dropping out. It also stops you from removing it if you were unaware of its presence!

The new clusters come complete with both the bulb units, bulbs and foam water repellent backing on the back so it really is a case of just swapping them over.



Carefully line up your new cluster with the bolts and plastic positioners and ease into position. Once in position, get one of the nuts and finger screw it on and repeat for the other two whilst gently holding the cluster in position.
Once lined up nicely apply a little gentle pressure to the cluster and using the ratchet or long socked (10mm) and tighten up the nuts until you are happy they are firmly in position. Pop the connector back into the socket on the rear of the removable bulb holder/unit.
Repeat for the other side and voilŕ!









Be warned, as these lights are [mostly] based on LED bulbs (running light and brake light) you WILL get a warning:



But when you have this, it is worth it...



But only for the brakes, nothing else. So the next task is to determine which wires I need to connect the resistors to to kill the Brake bulb warning. Then I need to find the wire that should be in position 4 of the socket on the left to power the passenger side rear fog.



All the bulbs are there, including the fog which is strange. What is missing appears to be the power as there are tracks in place for power and earth so some further digging (or help from a knowledgeable fellow enthusiast) will follow....


Edit: Update 1


Ok, so I got some resistors, as I was getting bored of seeing "Check Brake Light!" every morning and evening! Some discussion on swedespeed mentioned that 100w 6ohm resistors would run cooler than someone who used 50w 6ohm. A reasonable idea as the temperature measured was 98°!!!

This is (like) the one I ended up with: Linky



Where to put them though....! reinnie on swedespeed had some images and thanks to the big photophucket in the sky they were hardly every visible. Got them now so thanks to him for these images:

Left (as viewed from the rear remember): Pins are 3 and 6. | Pin 3 – Black and Brown | Pin 6 - Brown and Purple



Right: Pins are 3 and 4. | Pin 3 – Blue and Black | Pin 4 – Purple and Brown



When using the snap-lock clips (Yes, I know! These are temporary to make sure before I solder them in.) I noticed a couple of unusual things:
1) Left side connector has got two wires in each of the pin connectors.
2) One of the wires is thinner than the other, I used the thinner of the two as this "seemed" to be the correct one as per the photo.
3) On the right side, there was only one wire in each of the pin connector points!
4) By the looks, someone had been messing before me with the wires as there is a screw connector and another plug in the area behind the cover. Odd...

Clipped in and made sure there was a good connection, likewise on the right side, and tested. Warning was still there! Odd.
Got out, looked and one light not working! Got other half to press the brake and right nothing! Shut the engine off and contemplated for a minute. Opened the boot and started to check - I hadn't plugged the right connector back!!! Duh!!!!
Plugged in and tested again. Voilá! No warning and all lights working.

Next the fog light...

Des. . .

Original article
Attached Images
File Type: jpg S80_Rear_Light_In_the_Box1.jpg (129.7 KB, 0 views)
File Type: jpg S80_Rear_Light_In_the_Box2.jpg (180.5 KB, 0 views)
File Type: jpg S80_Rear_Light_Back-Left.jpg (157.3 KB, 0 views)
File Type: jpg S80_Rear_Light_Back-Right.jpg (189.2 KB, 0 views)
File Type: jpg S80_Rear_Light_Removed.jpg (151.8 KB, 0 views)
File Type: jpg S80_Rear_Light_Nr.jpg (197.5 KB, 0 views)
File Type: jpg S80_Rear_Light_Off2.jpg (177.3 KB, 0 views)
File Type: jpg S80_Rear_Light_Off.jpg (148.9 KB, 0 views)
File Type: jpg S80_Rear_Light_On.jpg (189.5 KB, 0 views)
File Type: jpg S80_Rear_Light_Warning.jpg (150.7 KB, 0 views)
File Type: jpg S80_Rear_Lights_Done.jpg (207.9 KB, 0 views)
File Type: jpg S80_Rear_Light_Left_Inner.jpg (151.7 KB, 0 views)
File Type: jpg Resistor.jpg (22.9 KB, 0 views)
File Type: jpg Left_pins_3+6.jpg (128.4 KB, 0 views)
File Type: jpg Right_pins_3+4.jpg (96.3 KB, 0 views)
__________________
Density:- Not just a measurement ~ It's a whole way of Life.! ! !
I drive a Volvo, Please Don't Get In My Way!
He shows up. People die. He vanishes.
People should not be afraid of their governments.
"He'll deliver more justice in a weekend than 10 years of your
Governments should be afraid of their people... "V"
courts & tribunals. Just stay out of his way." "I plan to."

Last edited by CTCNetwork; Oct 3rd, 2017 at 20:27. Reason: Added back link
CTCNetwork is offline   Reply With Quote
The Following User Says Thank You to CTCNetwork For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 04:33.


Powered by vBulletin
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.