|
200 Series General Forum for the Volvo 240 and 260 cars |
Information |
|
PCV System with aftermarket Webers Help please.Views : 1271 Replies : 22Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Sep 9th, 2019, 19:33 | #1 |
New Member
Last Online: Feb 2nd, 2020 19:03
Join Date: Jun 2019
Location: Maidstone
|
PCV System with aftermarket Webers Help please.
Hello, 17 years away from Volvos and I just knew I'd be back
I'm now the very proud recent owner of a December registered 1979 245GL Problem is someone has fitted twin Weber DCOE's to the car and I'm not sure it's been done correctly. I suspect the engine (crankcase) isn't breathing properly as there is oil all over the front of the engine (although that could be an oil seal) and there was a decent amount of engine oil in the air filters themselves. There is an aftermarket breather filter on the Valve cover which is fine but on the inlet manifold side below the manifold where I would suspect an oil separator box to be, there is just a big red blanking plate. (Although it does look original to me) Whereas on the exhaust side near the bell-housing there is just a spout of some sorts poking out which looks like it's spraying misty oil everywhere. I don't have the original air filter parts so I just want to make sure the crankcase is venting properly and install and oil catch can. Do I simply run a pipe from this 'spout' near the bell housing into the catch can and all is well or do I need to buy a few more parts? There are no more vacuum ports on the inlet manifold only the one for the brake servo and the one for the distributor vacuum advance. As I'm a new member I cannot post pics it seems?? Sorry for the essay. Thank you Last edited by spease1984; Sep 9th, 2019 at 21:33. Reason: I realised my pictures were too large so can add them at the beginning now. |
Sep 9th, 2019, 19:45 | #2 |
Trader Volvo in my veins
Last Online: Yesterday 22:41
Join Date: Dec 2004
Location: Anglesey
|
for photos just use imagur
You want to run the old breather box to a oil catch can |
Sep 9th, 2019, 19:56 | #3 |
New Member
Last Online: Feb 2nd, 2020 19:03
Join Date: Jun 2019
Location: Maidstone
|
Thank you for the reply.
There is no original air filter system left on the car only the K&N air filters on the twin webers. I was hoping I could simply run a pipe from the spout near the bell housing where all this oil seems to be spraying out to an oil catch can? I believe this spout went to a "Fire Trap" originally, but I'm afraid I don't know what that means. |
Sep 9th, 2019, 20:27 | #4 | |
Experienced Member
Last Online: Today 14:49
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
Sep 9th, 2019, 21:32 | #5 |
New Member
Last Online: Feb 2nd, 2020 19:03
Join Date: Jun 2019
Location: Maidstone
|
The advance for the distributor is in one of the ports for the manifold it looks like someone may have drilled and tapped this part of the manifold for the vacumm advance
|
Sep 9th, 2019, 22:42 | #6 |
Experienced Member
Last Online: Today 14:49
Join Date: Jun 2007
Location: L/H side
|
oh dear , by someone who did not understand how it worked , it would be better with it disconnected than work like that although you would miss out on some better fuel economy and a quieter engine when cruising...if it was all correct , nice pictures there and i'm sure those massive ports are liking the twin Webers . Have you checked the ignition timing with the vacuum pipe off ?
__________________
My comments are only based on my opinions and vast experience . |
Sep 10th, 2019, 13:56 | #7 |
Master Member
Last Online: Today 12:00
Join Date: Nov 2012
Location: London and Cambridge
|
Hi,
Nice car, I saw it on ebay a few weeks back. A few things: 1.) I have a 1978 245 with a single carb, with all the original parts in place. For cars that early there is one crankcase vent, which is from the cam cover (where you have a mini filter venting to atmosphere), from there a hose takes it to a flame trap, then the hose splits and one side goes to the inlet manifold and one side goes to inside the airbox, inside the filter. The blanking plate you photographed is where Volvo vented the crankcase on (only just) later cars. This webpage shows both a photo of what a flametrap is and also a line drawing diagram of how the hoses are routed. https://www.ipdusa.com/products/6860...rmarket-104325 2.) On my car the distributor advance hose goes to a port on the carb. As others have said, perhaps a port for this exists on one/both of your carbs. 3.) The barbed brass hose end you photographed is the coolant system drain, so that won't help you. Oil in that area is coming from something else - I suspect either the cam cover gasket, or the plug at the back of the head. Cheers |
Sep 10th, 2019, 15:24 | #8 |
Trader Volvo in my veins
Last Online: Yesterday 22:41
Join Date: Dec 2004
Location: Anglesey
|
There is no take off on the webers for a vac advance pipe
With the throttle closed to vac pipe is blanked on the original carb so no vac to the dizzy. As the throttle opens the dizzy then starts to see vacuum. How it is fitted you have too much vacuum at idle giving too much advance. The best long term answer is either going to a company like Aldon who can re-curve the dizzy or go with mapped ignition like this https://www.classicswede.co.uk/123tu..._18275269.aspx |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|