|
140/164 Series General Forum for the Volvo 140 and 164 cars |
Information |
|
Volvo 164 B30A inlet / exhaust manifold removal ?Views : 1296 Replies : 12Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
May 19th, 2019, 09:02 | #1 |
Junior Member
|
Volvo 164 B30A inlet / exhaust manifold removal ?
My 164 from 1973 was purchased after having stood still in a garage for 4 years.
After an effort to put the car back on the road within 16 miles one the core plugs leaked water. Examination has revealed that several core plugs are in poor shape. However to remove the core plugs on the side of the block with the inlet/exhaust manifold you need to remove the manifold. I have managed to remove all the nuts on the manifold with the exception of 2 nuts which are located centrally under the manifold and appear to be unreachable between no 3 and 4 cylinders. The nuts are above the metal return pipe for the heater system – making access more difficult. Does anybody have any hints / tips for removing the inlet / exhaust manifold on a B30 engine?
__________________
P1800S 1967 - Volvo 240 Estate 1986 - Everyday car...Volvo 164 1968 - Volvo 144 1967 - Volvo 144 1973 model - needs rust repair..and Volvo 164 1973. |
May 20th, 2019, 22:46 | #2 |
Junior Member
|
So the answer are offset spanners and a bit of patience.
Managed to get the inlet/manifold off but it took 20 mins to remove the last 3 nuts. With the manifold gone the core plugs are exposed and I will change them all.
__________________
P1800S 1967 - Volvo 240 Estate 1986 - Everyday car...Volvo 164 1968 - Volvo 144 1967 - Volvo 144 1973 model - needs rust repair..and Volvo 164 1973. |
May 21st, 2019, 16:55 | #3 |
VOC Member
Last Online: Yesterday 17:06
Join Date: Jul 2006
Location: Chatham
|
The problem with replacing the core plugs with the engine in situ is having enough room to swing the hammer to punch in the centres. Heavy hammer and a small socket, mind your fingers! Good luck with that. Clean and fully derust the holes in the block. A thin bead of Marine JB Weld is good where the plug seats especially if the block has some pitting.
|
May 22nd, 2019, 18:17 | #4 |
Junior Member
|
__________________
P1800S 1967 - Volvo 240 Estate 1986 - Everyday car...Volvo 164 1968 - Volvo 144 1967 - Volvo 144 1973 model - needs rust repair..and Volvo 164 1973. |
May 22nd, 2019, 18:21 | #5 |
Junior Member
|
so there is a picture of the manifold.
There is a 'mixing' unit at the centre of the manifold - should I open it and check it ? Does anybody knows how this works ?
__________________
P1800S 1967 - Volvo 240 Estate 1986 - Everyday car...Volvo 164 1968 - Volvo 144 1967 - Volvo 144 1973 model - needs rust repair..and Volvo 164 1973. |
May 22nd, 2019, 23:59 | #6 |
VOC Member
Last Online: Yesterday 17:06
Join Date: Jul 2006
Location: Chatham
|
Google says no picture at that url.
|
Tags |
b30 manifold |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|