|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
USA PV info pleaseViews : 1676 Replies : 21Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Feb 12th, 2021, 09:15 | #1 |
Member
Last Online: Today 16:13
Join Date: Feb 2019
Location: Oswestry
|
USA PV info please
I am fitting USA spec towel rail bumpers on my car. I have the details of cut outs in front wings for towel rail support arms but no information on the cut outs in the boot ( trunk) surround panel for the rear. Dimensions from the bottom edge of panel and from the wing seam would be greatly appreciated. Thank you.
|
Feb 12th, 2021, 11:26 | #2 |
VOC Member
Last Online: Yesterday 14:24
Join Date: Jul 2006
Location: Chatham
|
I don't think there are any actual cut outs. The tube that goes to the body has a filled end that is threaded and a bolt from inside the boot goes into that. There is a rubber grommet for the hole and I'd guess there is a load spreader washer inside. An extra brace inside to the chassis floor or inner wheel arches would make the bar much stronger but I don't think that was standard. The fronts are a bit beefier as they angle down to the chassis horns. You might have to slot the bodywork for those. Some reference pics here. I'm sure there are others if you search around.
https://classiccars.com/listings/vie...illinois-60073 |
Feb 12th, 2021, 17:10 | #3 |
Member
Last Online: Today 16:13
Join Date: Feb 2019
Location: Oswestry
|
Hi Derek thanks for your reply. Have just been to check on bumpers ( new) and the towel rail supports do indeed pass through the boot surround panel and presumably the flattened out end bolts to the inner wing !
|
Feb 14th, 2021, 04:38 | #4 |
Member
Last Online: Mar 1st, 2022 00:17
Join Date: Sep 2018
Location: Mexico City
|
See picture of my car rear bumper, not attached to wing
|
Feb 14th, 2021, 15:02 | #5 |
Member
Last Online: Today 16:13
Join Date: Feb 2019
Location: Oswestry
|
Well advarasi I have done quite a lot of research into this issue and looked at many photos on the internet and come to the conclusion that the original US spec bumpers did have a support arm as described in my original post. I can only presume your rear bumper is not original or has had the support arms removed and the corresponding holes they went through welded up!? My Stainless Steel replacement bumpers definitely have these arms on the front and rear towel rails. One day I will learn to post photos!
Perhaps a USA member might settle this discussion and hopefully supply me with the dimensions for the cut outs. |
Feb 14th, 2021, 15:15 | #6 |
VOC Member
Last Online: Yesterday 14:24
Join Date: Jul 2006
Location: Chatham
|
John Crosskey. If you read this can you provide any info? Please.
|
The Following User Says Thank You to Derek UK For This Useful Post: |
Mar 31st, 2021, 21:06 | #7 | |
Junior Member
Last Online: Apr 3rd, 2024 12:52
Join Date: Dec 2020
Location: WISBECH
|
Quote:
|
|
Apr 1st, 2021, 16:48 | #8 |
Member
Last Online: Today 16:13
Join Date: Feb 2019
Location: Oswestry
|
Thanks for photo, I actually have all the dimensions for the front cut outs but would really appreciate the measurements of the cutouts in the rear panel. Distance from bottom edge of panel to hole centre and distance from wing seam to hole centre would be very welcome and save any **** ups on my part.
|
Apr 2nd, 2021, 12:23 | #9 | |
Junior Member
Last Online: Apr 3rd, 2024 12:52
Join Date: Dec 2020
Location: WISBECH
|
Quote:
|
|
Apr 2nd, 2021, 22:21 | #10 |
Member
Last Online: Today 16:13
Join Date: Feb 2019
Location: Oswestry
|
That would be great,thanks.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|