|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
Information |
|
S40 Engine re-timing (Crank pulley sprocket No keyed)Views : 1822 Replies : 10Users Viewing This Thread : |
|
Thread Tools | Display Modes |
May 26th, 2020, 17:51 | #1 |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
S40 Engine re-timing (Crank pulley sprocket No keyed)
I am replacing the timing belt in my S40 1.6 Petrol 2009 (Engine code B4164S3).
I found Crank pulley sprocket No keyed after the sprocket removed, (Not mentioned on VADIS). I realized the Crankshaft is not at the position it should be so I need to re-timing, since the sprocket I moved out no keyed in it. How can I position Crankshaft at TDC and lock it. locking pin 9997201. I'm struggling to find the location of the hole which allows the locking pin 9997201 to go in.(No any marks can be found while crankshaft sprockets moved out) How to make both camshafts turn to the positions that the tool Camshaft setting bar (9997151) can applied ti fix camshafts. (No any makrs can be found on camshaft sprockets and the TB cases) I would be grateful if you could advice how I can get out this. Many thanks. |
The Following User Says Thank You to George24Forum For This Useful Post: |
May 26th, 2020, 22:32 | #2 |
Junior Member
Last Online: Mar 15th, 2024 00:35
Join Date: Aug 2019
Location: birmingham
|
Looks like you lock via a pin from the rear. Though other guide only mentions flywheel counter hold tool? maybe there is only one position the flywheel hold tool locks in, and its the same engine position as pin? Diesel was a lot easier
Not sure its same engine, but procedure looks the same, found a youtube video you put it in and rotate crank clockwise until pin stops you. https://www.youtube.com/watch?v=2Kpc0x6dn4o http://replace-timing-belt.com/how-t...-v50-1-6-2005/ https://drive.google.com/file/d/1NMk...ew?usp=sharing Last edited by daniel84uk; May 26th, 2020 at 23:15. |
May 27th, 2020, 21:41 | #3 |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
George24Forum
daniel84uk,
Many thanks for your very useful info. When I was searching the tool 9997201 got the pin, this should be Special Tool: 999 7152 on your ducu. Do I need this tool 9997201 for holding Flywheel while I reset crankshaft at TDC in order to install timing belt? Now the TB is off, (imaging this situation is similar to "Time belt broken", Damage to the valves and pistons can occur), how can I avoid the damage while make the 2 Camshafts in collect position? |
May 27th, 2020, 22:24 | #4 |
Junior Member
Last Online: Mar 15th, 2024 00:35
Join Date: Aug 2019
Location: birmingham
|
I think the flywheel tool might be just to prevent the pin being bent whilst tightening the pulley bolt? Thats its job on the diesel engine. It appears in the turtorial linked above its also being used to set the crank position too? i can only assume on this engine the flywheel tool must only slot into the flywheel at the same point the locking pin does.
I think i see your dilemma, You mean you arent able to turn the crankshafts to the right position when a piston is at TDC? Id first rotate the crank so that no piston is at TDC. ie back off a little from the crank locking pin. Then set the camshaft positions, the camshaft tool should only fit when both camshafts are in correct orientation. Then bring the crankshaft back into position against the locking pin. You should google this yourself though, dont use me as a single source of info. Ive only limited experience on a few motorbikes and cars, and certainly not this engine. Last edited by daniel84uk; May 27th, 2020 at 22:29. |
May 31st, 2020, 22:52 | #5 |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
Thanks daniel84uk
|
May 31st, 2020, 23:31 | #6 | |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
Tool 999-7201 and diamond friction washers for unkeyed crank
Quote:
Where can I get this tool 9997201 for holding Flywheel while I fix crankshaft bolt? Another question is about the crankshaft and its pulley& sprocket are unkeyed. The photos I attached shows both pulley and sprocket are smooth, not keyed. It's said they cannot firmly be assemblyed. http://technical-ceramics.3mdeutschl...ion-shims.html The video on the link above shows the positions between crankshaft/camshaft and sprocket change as time goes, and the timing will gone as well. The following link shows WARNING: Crankshaft sprocket NOT keyed to crankshaft. But do not mention the friction washer. http://replace-timing-belt.com/how-t...-6i-1998-2005/ My questions are In this situation, how can I make sure the timing will not be lost without the friction washer applied ? If the washers are needed where can I get the washer? If the washers are NOT needed (or cannot purchase it) how can I put the pulley and sprocket back to crankshaft and not lost timing? IF you are interested in this the link next is about this https://www.locostusa.com/forums/vie...hp?f=4&t=19372 |
|
Jun 2nd, 2020, 00:26 | #7 |
Junior Member
Last Online: Mar 15th, 2024 00:35
Join Date: Aug 2019
Location: birmingham
|
I think you are on your own on this one lol.
I dont see any washers listed on the parts page? I assumed it was a taper or friction fit. (Make sure it very clean if so) The sprocket wont move on the crank taper when the bolt is tightened if the belt is fitted and tensioned? The position of the sprocket on the taper is irrelevant if the crank is locked with the pin and cams locked with bar, just as long as the sprocket is in a position where the belt fits nicely? Assuming the flywheel tool is for counter holding only. You can get by without it by putting gearbox in high gear and jamming the brakes on with a piece of wood between pedal and seat. These are assumptions from looking at the documents only. Make sure it all makes sense in your head before proceeding. And turn it over by manually by hand before trying to start it so you know nothing going to hit. Last edited by daniel84uk; Jun 2nd, 2020 at 00:31. |
Jun 8th, 2020, 22:24 | #8 |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
S40 1.6 Petrol, crankshaft not keyed
Many thanks, daniel84uk
And I appreciate your info that is very helpful. The Crankshaft nose is very smooth, not keyed. Last edited by George24Forum; Jun 9th, 2020 at 00:29. Reason: Add a photo |
Jun 9th, 2020, 23:21 | #9 |
New Member
Last Online: Oct 7th, 2020 23:04
Join Date: May 2020
Location: Bristol
|
How to align camshaft to crankshaft without any originalmark
This post is continue my last post.
Last night or early this morning, I have a post ready to submit and click preview and it gone, so I need to typein to post it again. Any suggestion/advice are very appreciated. Now the situation is, Old timing belt removed, and original good/normal timing lost. crankshaft nose photo-1 crankshaft nose photo-2 There are not any marks in the sprockets/cam/crankshaft and on Timing belt case. (The white marks on photos below are made myself). My questions are 1. How can I recover the timing of cams and crankshaft while not any marks or how to align camshaft to crankshaft without any original marks. 2. In order to lock camshafts at right position, do I need to remove valvecover to use the tool 9997151 lock the camshafts. Is there another way to find what is the camshaft right positions? It seems to be necessary to remove the valve cover and apply the tool 9997151 in order to lock cams in the collect positions as VADI said: Rotate the engine clockwise until the special tool: 999 7151 can be placed in the grooves on the camshafts' trailing edge (see figure below). https://flic.kr/p/2ja6yN4 The following photos shows to lock camshafts the valvecover need opened. ValveCover_Flywheelside ValveCover_TimingBeltside But it said at youtube the PCV system it is better not to open it. https://www.youtube.com/watch?v=pYuszsm9v1c Does openning the valvecover be very difficult for DIY (tools, experience etc) 3. There is a part behind the cam sprocket. I marked in red, red mark -B- and red mark --A-- which has a hole that seems to pin into camshafts case, but not sure what is its function? Intake-side Exhaust-side Just in case of the photos not attached on text for some reason put the photos here https://flic.kr/p/2jam5Gg https://flic.kr/p/2ja61Wo https://flic.kr/p/2ja3ntd https://flic.kr/p/2ja6yN4 https://flic.kr/p/2jam5ET https://flic.kr/p/2jam5Gg https://flic.kr/p/2ja7kc5 https://flic.kr/p/2ja3nwe |
Jun 10th, 2020, 06:34 | #10 |
Junior Member
Last Online: Mar 15th, 2024 00:35
Join Date: Aug 2019
Location: birmingham
|
All the info you need has already been posted, there are no shortcuts i can see. Someone else might no of one though. If you arent confident ring a mobile mechnic?
Last edited by daniel84uk; Jun 10th, 2020 at 06:37. |
Tags |
b4164s3, crankshaft locking hole, s40, timing belt |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|