Hubcentric wheel spacers

T5Sweep · Jan 1st, 2018, 16:15

Who makes them for our rwd cars? I need some 25/30mm ones for my Canopus wheels.

Ben.

Laird Scooby · Jan 2nd, 2018, 00:00

There's a few for sale on fleabay :

https://www.ebay.co.uk/sch/i.html?_o...&_sacat=122154

Not sure what model you've got so you'll have to trawl through and find yours but they go from a few quid to £70-80 each, there are also a few different thread sizes for the studs (i know on my 1988 760 they're M12 x 1.5) so you need to check that as well before ordering anything.

If you find a likely one and it's not quite right, it's always worth contacting the seller to see if they can get hold of the one that is right.

Alternatively contact an aftermarket wheel specialist.

deeman940 · Jan 2nd, 2018, 03:41

you just missed some 30mm ones in for sale section...
I am going to order these 20mm ones shortly...

https://www.ebay.co.uk/itm/Hubcentri...53.m1438.l2649

Skyedriver · Feb 18th, 2018, 23:49

Opening up a whole can of worms:
I've been in discussion with a member here over a set of 16" wheels but they seem to have "gone to ground".
I did enquire with someone selling a set of 17" wheels on a well known auction site but I'd need spacers. But what he said was the later Volvo wheels have a different spigot size to the old 940's and that will create a second problem in that the spacer would need different spigot sizes inside to out if you see what I mean.
Anyone any guidance they could offer?
Thanks
Tony H

Laird Scooby · Feb 19th, 2018, 10:28

This might help :

https://www.carlsalter.com/volvo-wheel-fitments.html

Gives the PCD, studs, offset and centre bore (spigot) sizes. If you go up a level from that page, you can access the other wheel fitments listings and potentially find other alternative wheels that will fit. That's how i ended up with S/V40 wheels on my Rovers! Near perfect fit, had to buy some spigot rings as the Rover centre bore is 3mm smaller than the Volvo but other than that, PCD, offset etc were all spot on - even uses the same wheel nuts!

There is a feature on that site that lists wheel fitments by PCD so that might save you getting hubcentric spacers.

At the risk of getting my "cyber-ears" chewed off, what's wrong with the wheels you have?

Jan 1st, 2018, 16:15	#1
T5Sweep Master Member Last Online: Oct 24th, 2022 09:28 Join Date: Sep 2014 Location: Peterborough	Hubcentric wheel spacers Who makes them for our rwd cars? I need some 25/30mm ones for my Canopus wheels. Ben.

Jan 2nd, 2018, 00:00	#2
Laird Scooby Premier Member Last Online: Yesterday 09:22 Join Date: May 2012 Location: Lakenheath	There's a few for sale on fleabay : https://www.ebay.co.uk/sch/i.html?_o...&_sacat=122154 Not sure what model you've got so you'll have to trawl through and find yours but they go from a few quid to £70-80 each, there are also a few different thread sizes for the studs (i know on my 1988 760 they're M12 x 1.5) so you need to check that as well before ordering anything. If you find a likely one and it's not quite right, it's always worth contacting the seller to see if they can get hold of the one that is right. Alternatively contact an aftermarket wheel specialist. __________________ Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........

Feb 19th, 2018, 10:28	#5
Laird Scooby Premier Member Last Online: Yesterday 09:22 Join Date: May 2012 Location: Lakenheath	This might help : https://www.carlsalter.com/volvo-wheel-fitments.html Gives the PCD, studs, offset and centre bore (spigot) sizes. If you go up a level from that page, you can access the other wheel fitments listings and potentially find other alternative wheels that will fit. That's how i ended up with S/V40 wheels on my Rovers! Near perfect fit, had to buy some spigot rings as the Rover centre bore is 3mm smaller than the Volvo but other than that, PCD, offset etc were all spot on - even uses the same wheel nuts! There is a feature on that site that lists wheel fitments by PCD so that might save you getting hubcentric spacers. At the risk of getting my "cyber-ears" chewed off, what's wrong with the wheels you have? __________________ Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Jan 2nd, 2018, 03:41	#3
deeman940 Master Member Last Online: Apr 4th, 2024 17:58 Join Date: Oct 2015 Location: watford	you just missed some 30mm ones in for sale section... I am going to order these 20mm ones shortly... https://www.ebay.co.uk/itm/Hubcentri...53.m1438.l2649

Feb 18th, 2018, 23:49	#4
Skyedriver Master Member Last Online: Oct 31st, 2023 21:23 Join Date: Aug 2007 Location: Oban	Opening up a whole can of worms: I've been in discussion with a member here over a set of 16" wheels but they seem to have "gone to ground". I did enquire with someone selling a set of 17" wheels on a well known auction site but I'd need spacers. But what he said was the later Volvo wheels have a different spigot size to the old 940's and that will create a second problem in that the spacer would need different spigot sizes inside to out if you see what I mean. Anyone any guidance they could offer? Thanks Tony H

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)