|
XC90 '02–'15 General Forum for the P2-platform XC90 model |
Information |
|
ABS ringsViews : 20404 Replies : 64Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Feb 10th, 2018, 20:47 | #51 | |
New Member
Last Online: Jan 21st, 2021 20:05
Join Date: Nov 2017
Location: Barnsley
|
Hub puller.
Quote:
Mine was £75. Last edited by Thistrucker; Feb 10th, 2018 at 21:29. |
|
The Following User Says Thank You to Thistrucker For This Useful Post: |
Feb 10th, 2018, 21:27 | #52 | |
New Member
Last Online: Jan 21st, 2021 20:05
Join Date: Nov 2017
Location: Barnsley
|
Hudds Volvo breakers
Quote:
Last edited by Thistrucker; Feb 10th, 2018 at 21:41. |
|
Feb 10th, 2018, 21:40 | #53 | |
New Member
Last Online: Jan 21st, 2021 20:05
Join Date: Nov 2017
Location: Barnsley
|
Hudds Volvo breakers
Quote:
|
|
May 20th, 2018, 18:01 | #54 |
New Member
Last Online: May 31st, 2018 14:05
Join Date: May 2018
Location: Bishop's Stortford
|
Thanks for the advice in this thread. Just replaced ring today and all working fine. Two independent garages told me replacing the ring would probably not be possible and I would need a new driveshaft costing £400-500.
Hardest part was getting the strutt bolts undone and yes you can do with just undoing the top one and loosening the top one. It makes access to the driveshaft to get the new ring on tricky but can be done. Also definitely don't need to remove the ABS sensor - just unclip it. I heated up the new ring in the oven but wouldn't slide on easily. Maybe the driveshaft was too rusty and I didn't clean it enough or maybe just not hot enough. Anyway managed to knock it on gradually using brute force. All fine now and saved a lot of money. Maybe it won't last but good enough to get through next MOT. |
Jul 13th, 2018, 23:05 | #55 |
Master Member
Last Online: Feb 18th, 2024 18:07
Join Date: Dec 2014
Location: London, Wallington
|
Ive done mine today. Thanks fir the advises. One bolt method worked very well.
Thank you. [IMG] [/IMG]
__________________
Volvo Xc90 D5 2005 Euro 3 D5244T- Auto. Volvo V40 D2 2016 cross country Engine D4204T8. |
The Following User Says Thank You to sreviz For This Useful Post: |
Jul 18th, 2018, 18:17 | #56 |
Master Member
Last Online: Feb 18th, 2024 18:07
Join Date: Dec 2014
Location: London, Wallington
|
Ive checked today my drive shaft to see if all well after ABS ring replacement.
I see some movements in the dirve shaft where the cv boot meets the HUB. The movement is horizontal, in and out 3-4 mm. Is this normal. The other drive shaft near side has no movements at all(but then its splines are stuck with the hub) . I tightened the driveshaft bolt to 35NM and further tightened to 120 Degree. The bolt itself is tight and not loose. Can some one please advice me if this is normal or Do I have to re tighten the drive shaft bolt.
__________________
Volvo Xc90 D5 2005 Euro 3 D5244T- Auto. Volvo V40 D2 2016 cross country Engine D4204T8. |
Jul 19th, 2018, 13:54 | #57 |
Premier Member
Last Online: Yesterday 11:19
Join Date: Feb 2010
Location: North Northumberland
|
There should not be any movement.
Did you replace the drive shaft retaining bolt? They are strictly single use and should be replaced whenever they are disturbed. They are not too expensive from your local friendly dealer.
__________________
2018 V90CC D4, 2022 XC40 1940 Matchless G3, 1980 Moto Guzzi T3 Coming soon:- 1947Rover 14 P2 |
The Following User Says Thank You to 60041 For This Useful Post: |
Jul 19th, 2018, 17:56 | #58 |
Master Member
Last Online: Feb 18th, 2024 18:07
Join Date: Dec 2014
Location: London, Wallington
|
I didnt replace it with new one though. Thanks for that. I will buy volvo croydon near by me.
There was a rubber bush some thing like that in that bolt. Will that affect the torque? Thank you.
__________________
Volvo Xc90 D5 2005 Euro 3 D5244T- Auto. Volvo V40 D2 2016 cross country Engine D4204T8. |
Jul 21st, 2018, 09:15 | #59 |
Master Member
Last Online: Feb 18th, 2024 18:07
Join Date: Dec 2014
Location: London, Wallington
|
I replaced the bolt with a new one yesterday.
Strange the 3-4 mm lateral movement was there at the outer cc joint where it mates with the splines. The bolt itself is very tight. I over torqued it and snapped the head , hoping that tightening will cure the movement. I drilled the snapped bolt using an extractor. Lucky on that. Iam thinking that this movement was was already there in the car before I replaced the ring . Someone put double washer on the driveshaft bolt and also used custom made bolt to fit into the driveshaft by cutting the length of the bolt. Now my question is what makes the shaft move laterally. Please some experts here on the forum shed some lights so I can cure it. Iam inclined to some one fitted a bit longer drive shaft so even if the shaft is tightened properly or some one adjusted the camber might inserted extra washer in the bolt. Thank you.
__________________
Volvo Xc90 D5 2005 Euro 3 D5244T- Auto. Volvo V40 D2 2016 cross country Engine D4204T8. |
Jul 21st, 2018, 11:12 | #60 |
Master Member
Last Online: Feb 18th, 2024 18:07
Join Date: Dec 2014
Location: London, Wallington
|
I've attached the picture of the shaft from Google. The green arrow is the place where the lateral axial play is. Which means it is sliding 3 mm in the splines with the bolt also moving. As I said the bolt is torqued to 35nm and further angle tightend to 120 Degree.
Thank you. [IMG][/IMG]
__________________
Volvo Xc90 D5 2005 Euro 3 D5244T- Auto. Volvo V40 D2 2016 cross country Engine D4204T8. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|