|
850 / S70 & V70 '96-'99 / C70 '97-'05 General Forum for the 850 and P80-platform 70-series models |
![]() |
|
Moral support needed - T5 camshaft timing & sealsViews : 497 Replies : 3Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Member
Last Online: Mar 11th, 2024 19:42
Join Date: Jan 2009
Location: North Lincs
|
![]()
The unusual Bank Holiday weekend weather seemed like a good time to tackle a timing belt replacement on the C70
![]() On dismantling, however, a few 'issues' have cropped up.... Firstly, there was a fair amount of oil down the engine side of the inner timing belt cover. Not dripping, but you could see where it had coated the lower engine mount with 'crud'. I really should have performed the 'rubber glove test' to see whether the PCV system is functioning properly - but I haven't ![]() Is it likely that any camshaft seal 'weep' would cease if the PCV system was fixed (assuming it's faulty) - or has the damage been done? Or could it just simply be worn out seals - the engine has 156k on it? There's a trace of oil in the 'nose' of the inlet cam, but it's hard to see behind the exhaust VVT assembly. However, most oil appears to have been seeping down the exhaust side. Secondly, the exhaust VVT pulley looks a bit wrong. I would not have expected the fixing bolts to be so far up against the end of the adjustment slot, so that might need sorting, too ![]() It's one of those times when you really wish you hadn't bothered, and I can't quite decide how to proceed. I could just fit a new belt, get the car running again and test the PCV system. At least that needs to be functioning properly before any seals are replaced - or it'll just leak again! Are the seals hard to extract without damaging the sealing surface on the shaft? Sorry for rambling on a bit - just feeling a bit deflated at the moment ![]()
__________________
C70 T5 Coupe Auto 2000 MY Venetian Red |
![]() |
![]() |
![]() |
#2 |
VOC Member
Last Online: Today 22:16
Join Date: Mar 2008
Location: Northampton
|
![]()
As you are so far in with the timing belt, why not do the seals - as they are suspect - then when you start the engine do a glove test and proceed with the pcv if needed. It will save going into the belt again.
__________________
2001 V40 2.0lt Sport Lux - Daily Driver. 178k miles. 2003 C70 2.4 GT Convertible - Garage Queen. 67k miles. http://www.neptuno6benagil.com |
![]() |
![]() |
![]() |
#3 |
Member
Last Online: Mar 11th, 2024 19:42
Join Date: Jan 2009
Location: North Lincs
|
![]()
Well, as I unexpectedly had to move the car out of the way I just put everything back together again
![]() Some good news - the rubber glove was sucked a little into the oil filler, so the PCV system may not be too bad, and certainly not in itself responsible for the seal weepage.
__________________
C70 T5 Coupe Auto 2000 MY Venetian Red |
![]() |
![]() |
![]() |
#4 | |
mad mechanic
Last Online: May 11th, 2024 21:17
Join Date: Jun 2020
Location: horsham
|
![]() Quote:
be careful when purchasing the seals as theres some i seen supposed to be correct size as in they fit the hole but are not the same thickness as original infact nearly 2mm so the lip that seals ends up sitting different place now this may or maybe not be a problem but i thought better not to chance it and sent them back and ordered from a german supplier which was correct,ebay sellers no little and care even less ime and will happily say yes thats the right one even when its not because they rarely bother checking,good luck
__________________
volvo 850s estate 2.4 petrol manual 1994 |
|
![]() |
![]() |
The Following User Says Thank You to duke1 For This Useful Post: |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|