new to me s60 faults bcm-0111 info please

[tonka12]

i got a 265000 mile s60 d5 se my05 and have a few problems here are the codes I've read
bcm-a031
bcm-0111
bcm-a032
engine
ecm-6805
ecm2505
ecm-2501
ecm-2502
ecm-5000
any help greatly appreciated
cheers russ

[ShadeTek]

Originally Posted by tonka12

i got a 265000 mile s60 d5 se my05 and have a few problems here are the codes I've read
bcm-a031
bcm-0111
bcm-a032
engine
ecm-6805
ecm2505
ecm-2501
ecm-2502
ecm-5000
any help greatly appreciated
cheers russ

BCM:-http://www.volvopartsconnect.com/pages/index.cfm?action=viewPage&siteid=215102&pageid=110 17



'ECM 6805, BOOST PRESSURE CONTROL FAULT'

Fault code ECM-2502 Fuel pressure to high

Fault code ECM-2501 Fuel pressure to high

ECM-2505 Fuel Pressure - Too low pressure

ecm 5000 diagnostics says rpm sensor

[cookie]

loads of info on the 8605 code on the 163 engines

[ShadeTek]

Full list here:-

http://forums.t5d5.org/topic/9490-li...-phase-2-cars/

[cookie]

you need to clear the codes, go for a drive and see what re-appears, if you read with VIDA it will tell you how often each code is being triggered, often 1 fault will cause numerous codes

[SonyVaio]

Here is some info from VIDA with regards to your BCM codes.

BCM-0111 Communication between control modules. AYC stability control active for too long

Diagnostic trouble code (DTC) information BCM-0111

Note! The diagnostic trouble code (DTC) applies only to cars with dynamic stability and traction control (DSTC).

At each new ignition cycle, the brake control module (BCM) compares a value for the steering wheel angle from the steering wheel angle sensor with a calculated value. The diagnostic trouble code (DTC) is stored if the brake control module (BCM) registers that the deviation is too great.

The diagnostic trouble code (DTC) can be diagnosed at speeds above 10 km/h and when the steering wheel has been turned 10 degrees in either direction.

BCM-A031 Diagnostic trouble code (DTC) information

After the steering wheel angle sensor has been initialized, a check of the plausibility of the steering wheel angle is run.

The diagnostic trouble code (DTC) is stored if the check is not approved and speed exceeds 50 km/h.

The plausibility check can be completed even if BCM-A031 is stored, but before the ignition has been switched off. Diagnostic trouble code (DTC) BCM-0111 is also stored if the check is not completed within one minute.

The diagnostic trouble code (DTC) can be diagnosed at speeds above 50 km/h.


Substitute value

Active yaw control is blocked.

Possible source

The plausibility check of the steering wheel angle is not approved.

Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module.

BCM-A031 Communication between control modules. The tolerance check has not been run

Checking the diagnostic trouble codes (DTCs)

If diagnostic trouble code (DTC) BCM-A031 is stored on its own it must be erased.

If diagnostic trouble code (DTC) BCM-0111 is stored at the same time as BCM-A031, read off the diagnostic trouble codes (DTCs) from the steering wheel module (SWM).

BCM-A032 Communication between control modules. Stability control has been active for too long

Diagnostic trouble code (DTC) information BCM-A032

Condition

The diagnostic trouble code (DTC) is stored in the subsequent operating cycle (ignition off and ignition on) if the brake control module (BCM) performs an extended start up check of the DSTC system due to a number of different faults during the previous operating cycle.

Possible source

The diagnostic trouble code (DTC) has been stored in the previous operating cycle.

Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module.

[tonka12]

is the bcm number specific or are they the same on the rest of the range
many thanks russ

[atikovi]

Originally Posted by SonyVaio

Here is some info from VIDA with regards to your BCM codes.

BCM-0111 Communication between control modules. AYC stability control active for too long

Diagnostic trouble code (DTC) information BCM-0111

Note! The diagnostic trouble code (DTC) applies only to cars with dynamic stability and traction control (DSTC).

At each new ignition cycle, the brake control module (BCM) compares a value for the steering wheel angle from the steering wheel angle sensor with a calculated value. The diagnostic trouble code (DTC) is stored if the brake control module (BCM) registers that the deviation is too great.

The diagnostic trouble code (DTC) can be diagnosed at speeds above 10 km/h and when the steering wheel has been turned 10 degrees in either direction.

BCM-A031 Diagnostic trouble code (DTC) information

After the steering wheel angle sensor has been initialized, a check of the plausibility of the steering wheel angle is run.

The diagnostic trouble code (DTC) is stored if the check is not approved and speed exceeds 50 km/h.

The plausibility check can be completed even if BCM-A031 is stored, but before the ignition has been switched off. Diagnostic trouble code (DTC) BCM-0111 is also stored if the check is not completed within one minute.

The diagnostic trouble code (DTC) can be diagnosed at speeds above 50 km/h.


Substitute value

Active yaw control is blocked.

Possible source

The plausibility check of the steering wheel angle is not approved.

Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module.



BCM-A032 Communication between control modules. Stability control has been active for too long

Diagnostic trouble code (DTC) information BCM-A032

Condition

The diagnostic trouble code (DTC) is stored in the subsequent operating cycle (ignition off and ignition on) if the brake control module (BCM) performs an extended start up check of the DSTC system due to a number of different faults during the previous operating cycle.

Possible source

The diagnostic trouble code (DTC) has been stored in the previous operating cycle.

Note! This diagnostic trouble code (DTC) is not due to an internal hardware fault in the Brake control module (BCM) and must not be remedied by replacing the control module.

I have those same three codes. Has OP fixed the issues and if so, what was the problem?

[cheshired5]

Originally Posted by atikovi

Has OP fixed the issues and if so, what was the problem?

OP hasn't been on for 5 years.

[atikovi]

OK, just came upon this thread by searching those codes.