|
200 Series General Forum for the Volvo 240 and 260 cars |
Information |
|
240 drivers seatViews : 862 Replies : 4Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Feb 28th, 2006, 11:07 | #1 |
Member
Last Online: Apr 25th, 2024 13:39
Join Date: Jan 2006
Location: Bournemouth
|
240 drivers seat
I have just bought a fantastic 240 GLT saloon and am working my way through the little things that need fixing. I have noticed that the seat back on the drivers seat seems twisted - it is further back on the left side than on the right. Can the alignment be corrected ? - anyone with any tips or experience of this, let me know. Thanks. Steve
|
Feb 28th, 2006, 23:29 | #2 |
Former contributor
Last Online: Jul 2nd, 2022 07:54
Join Date: Dec 2004
Location: Rhosgoch, Anglesey
|
Had this as a MOT failure. Simple remedy - one of the bolts holding the back will have dropped out.
Mike
__________________
A Volvo is for life not just for Christmas! |
Mar 1st, 2006, 17:58 | #3 |
VOC President
Last Online: Apr 22nd, 2024 17:47
Join Date: Dec 2004
Location: Okehampton
|
240 seat back
I have had this problem with three 240's and have just done it on my present 240 GLT.
I am going to assume that that it is the part of the back that your left shoulder would rest against. It has gone flat and does not hold you in place very well. If this is the case the problem lies with the foam in the seat back. I don,t know why that particular place goes but, as I said it has happened in three of my 240's. I cured them all by taking out the seat, only four bolts holding it down, unplugging the heated seat cable and lifting the seat out of the car. Lay the seat on its 'face' and you will see the bottom of the seat back. There you will see some metal wire clips that are looped around a steel rod. This holds the front of the seat cover to the back. Cut them of with a good pair of side cutters or the like. Beware the wires are very sharp! Now take out the seat back tensioning plastic knob, it just unscrews. Having done this carefully slide the seat cover inside out up the back, a bit like taking off a sock by pulling at the ankle bit rather than the toe. When you get the cover right up to the head rest, (which you can also remove, I won't explain, it is so obvious if you have reached this stage) you should notice that the foam around the seat frame has split and the frame is poking through. I have cured this by using 'Evostick' to glue the splits back together and once when there was a hole where the foam had disintengrated I glued in a piece of firm foam from a sponge. I then got a piece of chamois leather and glued it right over the whole area of the repair. Then went and had a cup of coffee! This lets the glue set. When all is set carefully slide the cover back into place, again like putting a sock on by starting with it inside out and putting the toe bit on your foot first then folding the rest back over your foot. I hope that makes sense. When you come to where the bits of wire that you cut off were, use cable ties instead and they will pull the front and back together at the base of the backrest. Then screw in the lumbar support and finally bolt it back into place not forgetting the heated seat cable. This has cured all of mine and what a difference it makes not sliding about in the seat. It really is a very simple job so don't be put off. Good luck Dennis |
Mar 2nd, 2006, 10:49 | #4 |
Member
Last Online: Apr 25th, 2024 13:39
Join Date: Jan 2006
Location: Bournemouth
|
240 drivers seat
Thanks guys, I will whip the seat out and take a look. Not sure my vertebrae will hold out much longer ! Steve.
|
Mar 2nd, 2006, 12:23 | #5 |
Senior Member
Last Online: Jul 26th, 2010 09:55
Join Date: Dec 2003
Location: Taunton, Somerset
|
When you have the seat apart check the seat back frame also
Bulletin (Green Top from Factory) dated Oct 90 refersa to a change of foam and reinforcement of frame from chassis 425511 (244) and 879483 (245) This defect was 'known' by the factory prior to this and many were replaced under warranty and for safety reasons |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|