|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
"123" Programmable electronic ignitionViews : 5603 Replies : 36Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jul 8th, 2011, 06:30 | #31 |
Bury me in my Volvo
Last Online: Oct 18th, 2017 23:16
Join Date: Nov 2010
Location: Calgary (again!)
|
Hi. I can't tell you anything about your spark plugs, but that doesn't sound too bad, only your gas mileage does (right?).
I was going to post some new pics on here, but thought the better of it, and will post where I originally put up a few. I got a couple of days off, and manage to drive the car for the first time.... Looking-forward to getting the 123 on soon, and a few hours at the dyno. |
Jul 17th, 2011, 10:49 | #32 | |
Member
Last Online: Feb 9th, 2023 18:47
Join Date: Nov 2009
Location: Bristol
|
Quote:
Your plug looks on the rich side of OK, but don't forget it's the position of the SU needle in its jet at the RPM / throttle position you were using for the couple of minutes before the plug was 'read' that you are looking at. If the engine was idling for any length of time before it was turned off, then you are looking at the idle mixture. If you cut the engine immediately after a foot to the floor run up a long hill at 5000 RPM the plug colour will reflect mixture strength produced by the narrow part of the SU needle. This is the basis of the classic 'road test' method of calibrating SU needles. Fluctuating idle can be due to wandering ignition timing - hopefully not in this case - and air leaks around carb flanges / spindles and inlet manifold. Poor MPG means either the mixture is set too rich or the engine is set up so the throttle has to be opened more to get the power needed. The latter can be caused by ignition advance being too retarded. The general rule seems to be use the most advance you can at all times to get best power / economy but not so much that you get preignition / detonation. That is why vacuum advance is important for maximising fuel economy under part-throttle (cruising) conditions where cylinders are only part filled and the rate at which the mixture burns is slower - it needs firing up sooner. Des Hammill's book on tuning dizzy based ignition systems gives loads of good info on how advance curves work and gives rules of thumb to help 'curve' your dizzy. I have just bought myself a 123Tune for my Amazon rebuild. I hope to get it on the road by Christmas, but there is lots of welding & rebuilding to be done first! Can anyone help by providing a set of advance curves to get me going? My engine specs are: B20 2l bored +30 thou, K cam, twin 1 3/4 SUs, cast 4 into 2 ex manifold with Simons sport exhaust. Any help would be appreciated. All the Best, Tim |
|
Jul 18th, 2011, 05:40 | #33 |
Bury me in my Volvo
Last Online: Oct 18th, 2017 23:16
Join Date: Nov 2010
Location: Calgary (again!)
|
Hi Tim,
Good to know somebody else who has a 123Tune. By the end of August I will have mine all figured-out, so although we are not running exactly the same mill, I'll get back to you on that. Everything I've read suggests someone with a little bit of grey-matter can come-up with a workable curve that will work as a starting point, but we will see, I guess! I've only got about a week, but I'm hoping to dyno test mine. I'm curious at to what difference it will make as compared to a standard curve. (don't forget to upgrade your ignition wires if you haven't already.) Jim |
Jul 23rd, 2011, 09:52 | #34 |
Member
Last Online: Feb 9th, 2023 18:47
Join Date: Nov 2009
Location: Bristol
|
Hi Jim,
Thanks for your reply. Tony Barrett has promised to send me some B20 ignition curve data to get me started. You are welcome to see this if it will be any use. My Amazon is some way off being on the road. Took it round to my welder mate to get the rear arches sorted and found lots of cunningly painted glass fibre and a piece of roofing lead moulded to form the spare wheel well. I am no virgin when it comes to rusty cars but this one had me fooled! All said & done, it will make an expensive restoration but a good spares car. Meanwhile, I had heard of a 123 GT that was mounded up in a garage locally. Went to see it and could just make out an Amazon shape under the piles of crap that had accumulated over its 25 year layup. It will be a major operation to excavate it but I could just get round it for a look-see. A bit gouty around the rear wheel arches & the spare wheel well is non existent but it has not been previously bodged like my old one so actually looks to be a better prospect! A deposit changed hands and I should collect it soon. Now I have to find someone to buy my Riley 1.5 to fund the project! So, on to plan B - restore the 123GT and fit my rebuilt B20 engine and overdrive gearbox. Cheers, Tim |
Jul 23rd, 2011, 12:13 | #35 |
Amazoniste
|
BMC B Series, or Riley twin cam hemi?
__________________
Paul - 1967 Amazon 222S B20 o/d Estate & 1961 A-H Sprite Mk2 948cc WANTED - For '67 Amazon estate - offside rear quarter, preferably new old stock. |
Jul 23rd, 2011, 17:47 | #36 |
Member
Last Online: Feb 9th, 2023 18:47
Join Date: Nov 2009
Location: Bristol
|
|
Jul 16th, 2012, 20:08 | #37 |
Bury me in my Volvo
Last Online: Oct 18th, 2017 23:16
Join Date: Nov 2010
Location: Calgary (again!)
|
Finally got the 123Tune figured-out
Hi - sorry I haven't been on here much, but this seems worth sharing.
I was rooting around in my tool chest the other day, and found a vacuum pressure guage, so decided to hook it up, as I've still not really figured out the vacuum advance, even though I drove it across the country twice.... Oh-well. I've been a bit unhappy with the performance, it idles rough, it slow to respond off the line and valves are noisy. I thought maybe the valves needed adjusting, but am pretty sure the carbs were right. Well, when I hooked up the guage, I found pretty-near zero vacuum at idle, increasing with throttle. Looking around on the web (and previous posts) the standard vacuum seems to be the opposite!! Reason-being, it depends on where the vacuum pick-up is, and on my manifold, it is in front of the throttle/butterfly valve, not behind it, as is the case for most american junk, if not european. Sooo I looked a bit more on the net and confirmed SU's are different. I played-around with the settings for a couple of hours. As I was able to adjst the timing on the fly, I found that going from zero to fifteen degrees advance at idle, the rpm went from just over 800 to just under 1100rpm. Wow! This was definitely doing something! I backed-off the carbs, and and finally settled on the following: Vacuum adv. at idle of 13 degrees (on top of 8 degrees static), staying flat until the pressure is down 20%, then rapidly dropping the advance down to zero when the pressure (with no vacuum it is atmospheric pressure) drops by 25%. There are all kinds of units used, so let's just go with percentages. FYI, the rationale for advancing the spark at idle is that the mixture is lean, causing it to burning more slowly. One site (for performance cars) suggested 15 degrees, which I tried, but it seemed to run better with a little less. My engine is not stock - bored 30 thou over, shaved head, larger exhaust valves, ported and header. Centrifugal advance I had set to increase gradually at 1000rpm, up to a max of 21 + 8 degrees static to 29 degrees. Testing on a dyno might cause me to change my mind, but with no load, it seemed to hesitate, and I found it ran better with the advance kicking in at 1100rpm, going up to 30 degrees (total) by 3500rpm, maxing-out at 32 degrees at a hypothetical 8000rpm.... I believe the factory setting would be reaching the max of 36 at 3000rpm, so a considerable difference. Overall, the car starts better, runs quieter at idle, burns cleaner at idle, accelerates better at the bottom, and has a little more zip. I believe I had a curve in there for the advance which was the exact opposite for awhile, but changed it to flat (zero), because it was not running well, and I didn't know what else to do. I have some good gas-mileage figures, and plan to make a similar cruise soon, to see what difference, if any. It may be the more significant improvement is in the city, waiting for lights, etc.... I hope that helps, and am open to more suggestions!
__________________
James |
The Following 3 Users Say Thank You to Volvo Canadian For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|