Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > XC90 '02–'15 General

Notices

XC90 '02–'15 General Forum for the P2-platform XC90 model

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

XC90 - Westfalia Detachable towbar fitting guide

Views : 46400

Replies : 120

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Mar 21st, 2010, 21:42   #1
ABC
I've Been Banned
 

Last Online: May 4th, 2010 12:36
Join Date: Mar 2010
Location: UK
Default XC90 - Westfalia Detachable towbar fitting guide

Hi,

Am new to this forum, but read some of the advice given before I fitted a Westfalia detachable towbar to a MY2010 XC90 Active, so I hope this info on my install is some use for others.

I avoided the Volvo dealer fitted Towbar as I didn't like the way the Volvo towbar fitted, and the amount that was left visible when the towball was detached.

I bought the Westfalia towbar as it's invisible when detached. I got it from PF Jones website. Delivered next day for around £175.

I bought the Volvo 7 pin wiring kit from Volvo for around £50.

I had a friend help me fit the towbar at the weekend. Here's how we did it. ..

1) Remove spare wheel

2) Remove rear most exhaust hanger rubber and then undo two 10mm bolts holding next exhaust hangers on under rear axle. Allow exhaust to drop. It doesn't drop that much as it's supported about midway on the car body.

3) Remove exaust heat shield. 4 x 10mm nuts. Plenty of room to remove with a ratchet spanner.

4) No need to remove anything else on the bumper, or losen any part of the bumper trim - despite what the instructions will tell you.

5) In the car boot, lift luggage floor hatch , then remove the two triangular floor pieces on either side (they just pull up) and also the clip out panel just above on the left hand side.
Feel down on each side and pull off the foam strips covering the holes in the chassis rail (two more underneath the car covering the same holes)

6) Push in the Westfalia metal bolt guides / supports (see Westfalia instructions for more info ) on each side, and slide in the 6 bolts with washers.

7) Remove the tow ball from the towbar and offer up the towbar. We found it easier to offer up from the non exhaust side first over the exhaust pipes. Once in place the towball receiver will sit with about 2/3 over the existing half moon cut in the bumper and 1/3 obscured by the bumper. You need to make a small cut to expose the receiver but more on that later.

8) Once in place push the 6 bolts through from the inside of the boot.

9) Put the washers and nuts on. By pulling the bolts back in to the boot we could get a ring ratch spanner on for the majority of the thread on the bolt. Once bolt nearly pulled tight we switched to open ended spanner. One person with spanner on bolt in boot and one underneath car to tighten.

10) Remove battery cover and then start with Volvo wiring. It fits in from outside of car. Feed wiring loom through swivelling 7/13 pin socket holder on towbar. Then up through battery drain gromit in boot floor ( kit has new gromit on it already to replace the existing boot floor gromit)

11) Attach earth wire to existing earth point by battery.

12) Place wire loom behind battery and then through gap in trim to left hand side boot floor void (where bolts for towbar fitted)

13) Ignore Volvo instructions and don't remove any trim in boot on side. Instead feed wire up to fuse box and reach hand in and plug into socket on fuse panel and add a couple of fuses to same panel. Check your socket works by attaching to lighting board. All should be ok if you have followed these steps. No need for SW download from Volvo unless you want car fog lights deactivated (unlikely if you are fitting a 7 pin socket).

14) Trim bumper. All cuts are to the horizontal underside of the silver part of the bumper. If you lie on your back under car it makes it simple to cut around the inside of the towbar receiver and around "ears" on towball. I had to enlarge the existing half moon cut by about 1 cm. To avoid having to cut too big an opening I trimmed the towbar receiver cap ( for use when the towball is not being used) as the ears on this are bigger than needed).

Check your cuts as you go with the towball. No need to cut any more than needed to have towball engage /disengage cleanly.

15) When all is done nothing is visible from the rear of the car when the towball is not attached. Not even if you get on your knees and look. To see anything of the cut you would have to lie on your back under the bumper

All in all I am very pleased. I have saved over £300 and have a cleaner looking towbar install, and also by doing it myself I know exactly what was done (i.e bumper not removed etc) and I have managed to take the time to ensure I cut the bumper the absolute bare minimum I needed to - I am sure if I paid someone to fit this towbar they would have followed the template and made a much bigger cut than was needed which might have meant some of the cut was visible.

Hope this helps - will see if I can take a photo to show what it looks like and if I can post pictures on here.
ABC is offline   Reply With Quote
Old Mar 21st, 2010, 22:41   #2
bobdabuilda
Premier Member
 
bobdabuilda's Avatar
 

Last Online: May 31st, 2022 12:32
Join Date: Nov 2009
Location: south
Default

Superb write up ABC, look forward to seeing the pics of the install in due course.
bobdabuilda is offline   Reply With Quote
Old Mar 22nd, 2010, 03:03   #3
Volvopaws
New Member
 

Last Online: Aug 16th, 2010 23:45
Join Date: Dec 2009
Location: Manchester
Default

Yes, excellent write up! Particularly as I've been looking at PF Jones. Out of interest, why did you not go for their dedicated wiring loom instead of Volvo's own?
Volvopaws is offline   Reply With Quote
Old Mar 22nd, 2010, 09:47   #4
ABC
I've Been Banned
 

Last Online: May 4th, 2010 12:36
Join Date: Mar 2010
Location: UK
Default

In response to why did I buy the Volvo wiring....Well a good reason was that it was half the price of the non Volvo kits ( £52 delivered from Simon at FRF versus £105 from PF Jones) but the following were equally important ...

1) No warranty issues with the Volvo kit
2) Visibility of the installation instructions in advance
3) No messing - Volvo kit is 100% plug and play
4) Included the new boot floor gromit pre fitted, 7 pin socket already fitted


Here are some pictures...

The first picture shows the fuse panel where the Volvo wiring plugs in. You can easily reach in and plug the kit in (and take it out) without removing the side trim of the car as in the Volvo instructions.

In the second picture you can see the towbar just above the exhaust pipes. It's closer than I thought but doesn't touch . The silver bumper is pushed down a little in the middle. I think if I cut the bumper back a little more it would sit level, but I might see a fraction of the towbar receiver. I think I will keep it as is.

3rd picture shows the cuts I made. I need to file the curved edge down a little more for my liking. You can also see that I have cut the ears off the red plug. This just meant I got away with a smaller cut than I otherwise would have had to.

4th /5th picture shows the towball in use. The towball has changed from some of the earlier pictures I saw (old design was round tubing). I prefer this style so was happy that this is how it came.

Fitting the towbar couldn't be simpler. Remove the red plug, and simply offer up towball and it just clicks in to place. Turn the key and remove.

To remove unlock, pull handle out 1/2 inch and turn and the towball will disengage and you can lower out.

I store the towball in the boot to the right of the battery.
Attached Images
File Type: jpg 2.jpg (93.8 KB, 656 views)
File Type: jpg 3.jpg (45.2 KB, 609 views)
File Type: jpg 4.jpg (31.5 KB, 630 views)
File Type: jpg 5.jpg (41.1 KB, 598 views)
File Type: jpg 6.jpg (44.8 KB, 576 views)
ABC is offline   Reply With Quote
Old Mar 22nd, 2010, 14:05   #5
Volvopaws
New Member
 

Last Online: Aug 16th, 2010 23:45
Join Date: Dec 2009
Location: Manchester
Default

Unusual for Volvo to be cheaper! But thanks for your explanation - that makes it much easier.
Nice job as well looks very neat. What did you use to cut the bumper, just a standard hacksaw?
I want one to carry a bike rack. From your photos the towball does look quite close to the bumper. Would a bike rack clash with it do you think?
Volvopaws is offline   Reply With Quote
Old Mar 22nd, 2010, 14:31   #6
ABC
I've Been Banned
 

Last Online: May 4th, 2010 12:36
Join Date: Mar 2010
Location: UK
Default

Quote:
Originally Posted by Volvopaws View Post
Unusual for Volvo to be cheaper! But thanks for your explanation - that makes it much easier.
Nice job as well looks very neat. What did you use to cut the bumper, just a standard hacksaw?
I want one to carry a bike rack. From your photos the towball does look quite close to the bumper. Would a bike rack clash with it do you think?
I used a stanley knife to cut the bumper. I just took my time and kept checking as I went. In my view this is one of the benefits of doing it yourself compared to a towbar fitter who is against the clock.


I only use the towbar to carry a bike rack. I have a Thule 3 bike rack currently and there is no issue with the size of the gap between the towball/bike rack fixing and the bumper -with the bike rack attached there is still a good 6-8 inches clearance to the bumper. I think the photo I posted is deceptive so I can see why you would be concerned but I'll take a photo sideways on to show the clearance with the rack on.
ABC is offline   Reply With Quote
Old Mar 26th, 2010, 12:46   #7
Chris N
Member
 

Last Online: Feb 9th, 2017 21:40
Join Date: Mar 2010
Location: Witney, Oxfordshire
Default

Excellent write up! Thank you. I have just purchased the same towbar so this is perfect timing for me to read this thread.
What I wanted to ask though is the Volvo wiring has the "7 pin plug" fitted yet the plate that holds the wiring in place on the Westfalia towar is sealed. How did you manage to fit the plug fitted to the plate without cutting a slit though the backing plate?
Chris N is offline   Reply With Quote
Old Mar 26th, 2010, 13:50   #8
ABC
I've Been Banned
 

Last Online: May 4th, 2010 12:36
Join Date: Mar 2010
Location: UK
Default

Quote:
Originally Posted by Chris N View Post
Excellent write up! Thank you. I have just purchased the same towbar so this is perfect timing for me to read this thread.
What I wanted to ask though is the Volvo wiring has the "7 pin plug" fitted yet the plate that holds the wiring in place on the Westfalia towar is sealed. How did you manage to fit the plug fitted to the plate without cutting a slit though the backing plate?
Yes - that was a surprise to me espcially since I had already fitted the wiring the week before. I had to remove the wiring and start again. I fed the wiring through the towbar 7 pin socket plate. It was a squeeze and I had to feed the larger of the electric plugs through first without any cable to give enough room to get the plug through side ways on.

So - if that makes sense - basically fit the towbar, them feed wiring loom through plate starting with biggest plug , then into car leaving 7 pin socket as last to come up to the plug.

I did think about cutting the round plate when I realised my mistake ( of having fitted the wiring before the towbar) but decided against it and was glad it worked out ok.
ABC is offline   Reply With Quote
Old Mar 26th, 2010, 13:57   #9
ABC
I've Been Banned
 

Last Online: May 4th, 2010 12:36
Join Date: Mar 2010
Location: UK
Default

Quote:
Originally Posted by Volvopaws View Post
Unusual for Volvo to be cheaper! But thanks for your explanation - that makes it much easier.
Nice job as well looks very neat. What did you use to cut the bumper, just a standard hacksaw?
I want one to carry a bike rack. From your photos the towball does look quite close to the bumper. Would a bike rack clash with it do you think?
Here are the photos to show clearance ...
Attached Images
File Type: jpg 1.jpg (96.6 KB, 427 views)
ABC is offline   Reply With Quote
Old Mar 26th, 2010, 16:41   #10
Britsud
Anycolouraslongasitsblack
 
Britsud's Avatar
 

Last Online: Mar 20th, 2012 00:38
Join Date: Mar 2010
Location: swadlincote
Default

Geat job and write up, Would be nice if we had a, how to do column on our forum would make searching for these great how too,s far better.

Just for interest to our readers my wife has a civic type r just take a view at this forum
some people are rely dedicated i dont no where they find the time

www.civinfo.com
__________________
2008my xc90 sport,Polestar 205bhp, Flip down DVD, Full intergrated phone volvo on call, RTI Satnav full post code, privacy glass, Winter pack, Family pack, calcite soft leather, .Bi-xenon active headlights, Brembo discs Redstuff Pads.
Britsud is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 16:11.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.