|
S40 / V40 '96-'04 General Forum for the Volvo S40 and V40 (Classic) Series from 1995-2004. |
Information |
|
Replacing the Drop Links (Anti Roll Bar Links)Views : 7759 Replies : 83Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Aug 24th, 2016, 07:33 | #81 |
What is this I don't even
Last Online: Aug 31st, 2017 08:01
Join Date: Mar 2015
Location: *
|
Oh, so the section only contains copies. Alright then.
|
Mar 14th, 2021, 14:32 | #82 |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
[SIZE="3"]If you are experiencing an irritating rattle when you drive over rough surfaces but no rattling noise when on smooth surfaces, then most probably, your drop links (also known as Anti Roll Bar Links) are shot and need replacing. Also you should change the drop links if the rubber boot is perished.
I had no rattle on mine, but the rubber boots/gaiters were split and it was time for them to be changed. I normally go for Volvo original parts as they last a lot longer than some of the aftermarket rubbish out there. However I have read a lot of positive comments about the MEYLE HD drop links and they come with a 4-year guarantee and cost me only £35 for both sides. The Volvo part number for the Phase 2 S/V40 is 30884179 and the MEYLE part number I bought is HD 516 060 0009/HD. They are 267mm in length. Tools that you will need: 15mm spanner T30 torx key wire brush WD40 or similar lubricant spray/penetrating oil Jack and axle stand Additional things you might need if you can't get the nuts off Blow torch Angled grinder Loosen the wheel nuts and jack the car up and support it on an axle stand Remove the wheel and you can now see the drop links (highlighted in yellow in the photos). If they are covered with dirt, use the wire brush to clean it up and spray some penetrating oil on the drop links screw threads and let them soak for a bit. Time for a cuppa or a beer. Ideally, you could spray them the day before, as it will make things easier. The drop links are held at each end by a nut. In order to undo the nut you need to use a T30 torx key in the centre of the screw thread so you restrain the screw whilst undoing the nut. If you are lucky enough and the thread of the screw is not very rusted, you will undo the nut easily. If the nut starts to get hard to turn, then stop and screw it back in. Try not to force the nut too much because you will most probably round off the torx thread, or bend the hell out of your T30 torx key like I did. If you are still struggling with it, then you can use the blow torch and if this fails too, then use the angle grinder. In my case, 3 nuts came off nice and easy but one of them bend the hell out of my Cr-Mo impact socket torx..... I had to use the angle grinder to get it off. Another method is to rip the rubber gaiter and use some mole to hold the screw while undoing the nut. Old drop link with split gaiter Old vs new drop links Fit the top part of the drop link first using the T30 torx to secure the middle and tighten the nut You will notice that the bottom part of the drop link is a bit lower than where it's meant to go (see photo above. Place the jack under the wishbone and raise it until the bottom part of the drop link is level with the hole it is meant to go into and screw in the nut...... Job done!!!
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
Last edited by gatos; Mar 14th, 2021 at 15:49. |
The Following 3 Users Say Thank You to gatos For This Useful Post: |
Mar 15th, 2021, 22:10 | #83 |
Master Member
Last Online: Apr 25th, 2024 11:15
Join Date: Oct 2011
Location: Great Yarmouth
|
Thanks for taking the time to repost photos Gatos.
I know this is one of the relatively easier jobs to do but for the first time people out there. As they say "A picture paints a thousand words" |
The Following User Says Thank You to lynns hubby For This Useful Post: |
Mar 16th, 2021, 15:26 | #84 |
Premier Member
Last Online: Today 09:14
Join Date: Mar 2017
Location: Wessex
|
Excellent guide, thanks.
__________________
Non bowus drawi, non ridus horsi, non snoutus injecti! |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|