|
700/900 Series General Forum for the Volvo 740, 760, 780, 940, 960 & S/V90 cars |
Information |
|
water lossViews : 1783 Replies : 40Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jul 9th, 2019, 20:28 | #1 |
Member
Last Online: Jan 2nd, 2020 15:28
Join Date: Jan 2013
Location: near london
|
water loss
hi, had the waterpump replaced as water was gushing out of the rubber seal as fast as i put it in, i know the valve inside in the drivers well leaks which will also get replaced asap but a round trip of about 5 miles empties the header tank with no visible signs of a leak anywhere apart from the wet floor on the drivers side? which i dont think is where all the water escapes to!
any thoughts its a 940 2.3 turbo estate 94 auto |
The Following User Says Thank You to volvomadwoman For This Useful Post: |
Jul 9th, 2019, 20:54 | #2 |
Premier Member
Last Online: Yesterday 23:05
Join Date: May 2012
Location: Lakenheath
|
Get yourself one of those LED torches/headtorches that you have full brightness or a dimmer setting on. Find somewhere really dark without sky-glare, street lamps or similar to park at night, get your torch/headtorch on the DIM setting, open the bonnet and start the engine. You should be able to have a look round with the torch and see any water escaping.
The reason this works is because the water, if it's coming out in a jet somewhere will be a high speed series of water droplets. Using the LED torch on full brightness won't show it up as it's steady light so while you may (if you're lucky) catch the stream of water droplets, the surrounding area will also be as bright so will be difficult to see. On the DIM setting, the LED is pulsed at high frequency, rather like a strobe light. It's not visible to the naked eye but point it at a jet of water and it appears to "freeze" the water drops mid-air, much like a timing strobe light works. I found the cause of a mystery misfire and water loss using this method on my last 740 - pinhole in the top hose that was spraying backwards all over the distributor cap and plug leads! Worth a try as it's relatively cheap/free to try and might save you a lot of head scratching!
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
Jul 9th, 2019, 23:46 | #3 |
Master Member
Last Online: Oct 8th, 2022 22:22
Join Date: Sep 2016
Location: Auckland
|
If Dave's suggestion doesn't work, get the system presurre-tested and gas test the coolant for combustion byproducts.
FYI, I had a series of biblical component failures in the coolant system on a similar age 230FT. The heater valve begat the bypass tube begat the waterpump begat the radiator begat the head gasket... Its the nature of a mechanical device that related components will fail at around the same time. |
The Following User Says Thank You to aardvarkash10 For This Useful Post: |
Jul 9th, 2019, 23:58 | #4 | |
Premier Member
Last Online: Yesterday 23:05
Join Date: May 2012
Location: Lakenheath
|
Quote:
The way you've written it though Ash i was kind of expecting a punchline about ".....begat the Great Flood" or something. I call it "The Domino Effect" - one component falls down and a load then fall down after it in sequence. These days if something relatively minor goes, i tend to do a "pre-emptive strike" on all related bits, make sure they're ok and renew any that look slightly suspect. Might cost a little more at first than just fixing the basic fault but it saves a lot more money in the long run.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
Jul 10th, 2019, 19:46 | #5 | |
Premier Member
Last Online: Feb 11th, 2023 20:32
Join Date: May 2010
Location: Blyth, Northumberland
|
That’s a Goodun
Quote:
Just a thought, the LED head torch I commonly use has three brightness settings using only 4 LEDs then 8 then all 12. Does your method still apply or does the torch have to have some other method of dimming the LEDs? Last edited by Ian21401; Jul 10th, 2019 at 19:51. |
|
The Following User Says Thank You to Ian21401 For This Useful Post: |
Jul 10th, 2019, 20:52 | #6 | |
Premier Member
Last Online: Yesterday 23:05
Join Date: May 2012
Location: Lakenheath
|
Quote:
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
Jul 10th, 2019, 22:29 | #7 |
Junior Member
Last Online: Jul 3rd, 2022 20:15
Join Date: Feb 2018
Location: Bath
|
Hi are you sure the waterpump is now water tight? 5miles out of the header tank is obviously very bad. My 940 was leaking this badly once and it was leaving a good sized puddle when parked up. My problem was the pump, and it was a flood after each drive. Look for coolant in the oil pan at the front and also further back the pipes by the oil filter can go very bad. Hope this helps
|
The Following User Says Thank You to Volvoluke For This Useful Post: |
Jul 10th, 2019, 22:38 | #8 | |
Premier Member
Last Online: Yesterday 23:05
Join Date: May 2012
Location: Lakenheath
|
Quote:
As that was the original problem leading to the water pump replacement the common sense thought would say that's not what it is, however experience has shown recently that a lot of the new pumps leak badly, even when fitted correctly. It's possible they fitted it wrong or didn't clean old limescale off properly causing the problem though.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
Jul 10th, 2019, 23:06 | #9 |
Master Member
Last Online: Apr 25th, 2024 11:15
Join Date: Oct 2011
Location: Great Yarmouth
|
Not wishing to teach anyone to suck eggs here but its also worth noting that when fitting the new pump it needs to be "Snugged" up to the large rubber seal at the Head. That's why the bolt holes in the pump are elongated.
|
The Following 2 Users Say Thank You to lynns hubby For This Useful Post: |
Jul 11th, 2019, 07:13 | #10 |
Premier Member
Last Online: Feb 11th, 2023 20:32
Join Date: May 2010
Location: Blyth, Northumberland
|
I confirm that.
I had great difficulty with that top seal when I replaced my water pump some time ago. The “O” ring on the end of the rigid pipe into the back of the pump also needs to be carefully snuggled up into the pump. Is the pump to block seal leaking? It’s difficult to see it when everything is back in place.
Last edited by Ian21401; Jul 11th, 2019 at 07:16. Reason: Add text. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|