|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
fitting headrestsViews : 6156 Replies : 14Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Mar 21st, 2010, 21:41 | #1 |
foot in mouth specialist
Last Online: Sep 6th, 2016 22:55
Join Date: Sep 2009
Location: Dublin, Ireland
|
fitting headrests
Had some time to myself this weekend, so finally got to give the car a bit of love..
Here's a quick how to on a Headrest retrofit into a ’66 Amo.. 1. Source 2nd hand headrests from a friend (thanks Mitch) 2. Find a copy of Fredrik Lofter’s headrest install guide (thanks Derek) 3. Grab some tools. These ones worked for me. Pic 1 4. See it’s 10am, grab a beer and a big Philips screw driver. 5. Take off the first seat by way of 4 screws in the sides (2 per side) 6. Compare seatbacks to donors ensure they’re pretty similar. See Pic 2. 7. Move on to the next phase of actually opening the seatback. Basically get your big pliers out and your needle-nose ones and turn the hog-rings around until the split is shown, then just twist apart and unhook the trim edging. (sorta feels reminiscent of trying to undo your first bra, you need to be very gentle, and you’re not quite sure what you’re going to find...) 8. Using the flats of two big screwdrivers and the well shaped, rounded, handle of your biggest pliers, prise open the channel that holds the front annd back of the seat together.. 9. There’s stick your hand up the shirt and find a little metal thing about halfway up inside the seat you need to unhook, and then it all slips out very easily after that. 10. The moment of truth is lifting up the foam and finding the two supports the Volvo guys were kind enough to weld in place. (Apparently only cars ‘66+ have these..) Thank god mine had them... 11. Remove tubes and bits from donor seats and insert into new homes. The plastic catches are pretty difficult to get into the receivers, so i took the frame outside, turned it upside down and banged them up and down on some carpeting until they were in enough. 12. Pull the cover back over the seat and be sure to line the cover up properly with the contours of the stuffing. Where the two tubes pull through the covers, get your craft knife out and cut two holes. Fit the securing nut and washer in place and have another sip. 13. Get your pliers and white gym towel and start slipping the front and rear seat trim back into the securing channel 14. I found the best way to bend the channel back into place was to clamp it up.. Pliers and such only wreck the vinyl. 15. NB: Go easy pulling the shirt back on, otherwise you might tear it like i did.. Feck it anyway. 16. Try on your new headrest for fit.. looks ok so far 17. Have another sip and go grab the next seat and repeat the process 18. Pop up to Halfords and grab a can of vinyl paint. Prepare and paint headrests.. About 4 coats did it for me.. 19. Fit headrest and admire your work.. 20. Go for a drive to test them out.. Stop in at B&Q and pick up 6 metres of green and black strapping (40mm). Replace tired Pirelli webbing... 21. Job done.. Time to complete = about 3 hours, minus waiting for paint to dry Difficulty rating = 1 beer. Satisfaction = great |
The Following 9 Users Say Thank You to redcar For This Useful Post: |
Mar 21st, 2010, 22:43 | #2 |
Premier Member
Last Online: Today 06:45
Join Date: Jul 2007
Location: Connecticut, USA
|
RC;
My compliments on a good documentation...the bra analogy was unique and colorfully descriptive...I like it! Looking back on the work, do you think it might have been possible to install HRs without "undressing" the seatback to get access to the innerds and frame? ...by feeling around and locating mounting tubes, cutting holes for access, and doing the rest of work externally? This is the way the retrofit instructions presented it (Fig. 3), and it would sure make for a lot less work! I'd be interested in your experience...I'll certainly link this thread in my article: http://www.sw-em.com/headrest_upgrading_notes.htm Cheers from Connecticut! Last edited by Ron Kwas; Mar 21st, 2010 at 22:46. |
The Following User Says Thank You to Ron Kwas For This Useful Post: |
Mar 21st, 2010, 23:43 | #3 |
Premier Member
Last Online: Apr 17th, 2024 12:54
Join Date: Jul 2008
Location: Co. Cork, Ireland.
|
Well done Gareth! A great article. Thats a nice job you have done. I must say the vinyl paint works well too. I can see this ending up in the "articles" board, but beer at 10am, tut tut...
Hugh.
__________________
1970 Volvo Amazon 131 with a B20A and an M40. |
Mar 22nd, 2010, 06:27 | #4 |
Chief Bodger
Last Online: Yesterday 18:30
Join Date: Oct 2009
Location: Aberdeen
|
Looking good...
|
Mar 22nd, 2010, 09:37 | #5 | |
foot in mouth specialist
Last Online: Sep 6th, 2016 22:55
Join Date: Sep 2009
Location: Dublin, Ireland
|
Quote:
i'd be reluctant to try putting the tube in without pulling the covers off. the plastic bit at the top of the tube is a lot wider than the hole you're cutting, so you'd probably end up ripping the vinyl.. tbh it only took an hour or so per side, and is not beyond the reach of any person who owns a classic. |
|
Mar 22nd, 2010, 09:39 | #6 |
foot in mouth specialist
Last Online: Sep 6th, 2016 22:55
Join Date: Sep 2009
Location: Dublin, Ireland
|
|
Mar 22nd, 2010, 12:22 | #7 |
Amazoniste
|
Many thanks for the info Redcar & Ron - I already have a pair of factory headrest backrests, but they don't quite match the rest of my interior (Volvo used far too many different reds.....), so it has always been the plan to install them into my original backrests. Your posts will prove invaluable!
Btw, does anyone actually consider these headrests to be especially comfortable? The alternative accessory ones that are in Ron's link look much better from that perspective (I find that the factory fitment headrests are too far back), and am thinking of getting some cushions made to clip / tie around them, so that the headrest reaches further forward. Also, has anyone ever fitted headrests to the rear seats, in particular to an estate?
__________________
Paul - 1967 Amazon 222S B20 o/d Estate & 1961 A-H Sprite Mk2 948cc WANTED - For '67 Amazon estate - offside rear quarter, preferably new old stock. |
Mar 22nd, 2010, 20:00 | #8 |
VOC Member
Last Online: Jan 16th, 2023 22:07
Join Date: May 2009
Location: teesside
|
them headrests look great,like what uve done with the vinyl paint,id like to do that to my own amazon....but its finding a pair of headrests and tubes!!
|
Apr 27th, 2012, 12:40 | #9 |
Amazoniac
Last Online: Nov 18th, 2014 13:53
Join Date: Oct 2010
Location: Essex
|
|
May 1st, 2012, 18:23 | #10 |
Master Member
Last Online: Oct 1st, 2023 14:39
Join Date: Dec 2004
Location: leics
|
Nice article. Should this be added to the jobs and guides section of the forum along with Ron's added info and links?
|
The Following User Says Thank You to jimbo1593 For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|