|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
B18 EngineViews : 622 Replies : 9Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 12th, 2023, 14:18 | #1 |
Junior Member
Last Online: Apr 6th, 2024 15:21
Join Date: May 2007
Location: Sittingbourne
|
B18 Engine
I am taking my engine out over winter.
I am going to give it an overhaul, but whilst it is out i wish to enhance the perfomance. Any thoughts advice on polishing heads, cams flywheels pistons painting the block please most welcome. |
Dec 12th, 2023, 14:51 | #2 |
Experienced Member
Last Online: Today 11:23
Join Date: Jun 2007
Location: L/H side
|
I suppose the obvious is fit a B20...?
__________________
My comments are only based on my opinions and vast experience . |
The Following User Says Thank You to Clan For This Useful Post: |
Dec 12th, 2023, 15:20 | #3 | |
Senior Member
Last Online: Today 10:09
Join Date: Sep 2021
Location: MILTON KEYNES
|
Quote:
If you can’t get the crank balanced at least balance the pistons and con rods Aim is to get every piston within one gram, every small end and big end within 1 gram It won’t be a lot more powerful but a good smooth engine, a cam will give more power but it’s a trade off be sure what you want from the engine before selecting, large lifts put a lot of strain on the valve train and big overlap causes a lumpy idle, if your going for more overlap you need a good exhaust manifold to make full use of the overlap |
|
Dec 12th, 2023, 16:14 | #4 |
Master Member
Last Online: Apr 25th, 2024 13:36
Join Date: May 2017
Location: New Milford, Connecticut
|
My understanding is that the best money spent will be on the head. Find a place that can modify your head properly.
I had a head ported as part of a race engine build. It was great, but I didn't know better. Later, I cracked that head and slapped on my spare "flowed head", i.e., ported on a flow bench. That head was noticeably better and allowed the engine to continue to pull to 100+ mph. I could suddenly catch and pass cars that were always out of my reach. For a street build, I would try to send out to a qualified shop. You might also consider a lightened flywheel. This is not a recommendation for a shop, just a place to start looking. http://www.v-performance.com/product...formance_heads Also see http://www.v-performance.com/article...h_updates.html |
The Following User Says Thank You to blueosprey90 For This Useful Post: |
Dec 13th, 2023, 01:26 | #5 |
Master Member
Last Online: Apr 25th, 2024 13:36
Join Date: May 2017
Location: New Milford, Connecticut
|
I'm going to supplement my prior post. I'm not sure what you are looking for, but you might also try to match a camshaft with whatever head work you have performed. A little extra lift and duration on the cam complimentary to whatever head work you have done. After that, compression is always a good thing, subject, of course, to what fuel you might be limited to by budget or otherwise.
|
Dec 13th, 2023, 08:25 | #6 |
Senior Member
Last Online: Today 10:09
Join Date: Sep 2021
Location: MILTON KEYNES
|
This link from Amazon Cars gives a good idea of getting the best out of a standard B18 without spending lots of cash, rally spec rather than race
https://www.patreon.com/posts/543766...=postshare_fan |
The Following User Says Thank You to Rustinmotion For This Useful Post: |
Dec 13th, 2023, 12:10 | #7 |
Chief Bodger
Last Online: Today 12:32
Join Date: Oct 2009
Location: Aberdeen
|
What B18 do you have? If it's a A engine then there's a good amount of added HP by going to the later B18B spec or even D cam with 10:1 CR with twin SUs. Tidying up the ports directly under the valves and removing the step on the valve stems is probably far enough for a nice street engine. Going oversize for the bottom end will help with torque but I think you need to be careful with the B18 as you might hit a water jacket due to the poor castings. Engine work isn't cheap.
__________________
One day I will get rid of all of the rust. Last edited by Burdekin; Dec 13th, 2023 at 12:55. |
The Following User Says Thank You to Burdekin For This Useful Post: |
Dec 13th, 2023, 16:05 | #8 |
Master Member
Last Online: Yesterday 15:46
Join Date: Jul 2020
Location: Saskatchewan, Canada
|
If the engine is close to original then chances are the camshaft and lifters are due for replacement because of surface spalling. This was a B18 / B20 materials flaw right up until the early 70s. If you are replacing the camshaft, then consider contacting Tinus Tuning and ask for his recommendations on a suitable camshaft. They should ask what compression ratio, what carb arrangement and what exhaust system. You may be able to engage them in a conversation as to "this is what I want, what do you recommend". Cam selection will be dependent on carb selection and compression ratio. In particular, SU carbs do not idle well with long duration camshafts. Twin SUs will work with a D grind cam; but, it won't be a nice smooth idle if that is important.
As Burdekin notes, if you have a B18A the simple path to more power would be change to a B18B spec or Clan's suggestion to just transplant a B20B into the car. A used B20B would probably be cheaper than the machine work required to upsize the B18 and a B20 head has larger valves (get a B20E head) and proper valve seals as opposed to those silly umbrella things on the B18. Whether you currently have a high compression engine or want to increase the compression ratio, decking the block and machining the piston crowns so that the tops are flush with the deck will allow you to establish a correct squish band in the combustion chamber which will allow you to run the correct amount of ignition advance without incurring detonation. Unless you have access to a technician with a flow bench and prior knowledge of old school head modification, don't bother with modifying the combustion chamber and the ports. The #1 problem with B18 / B20 head design is the exhaust port and the > 90 bend the exhaust gasses take exiting past the valve. Fixing that problem is a lot or work which requires welding in filler on the bottom of the port floor. Checking the combustion chamber volumes to make sure they are matched which means matched compression ratios on all four cylinders would be a good thing. As noted by Rustinmotion a multi angle valve job with hardened inserts on the exhaust valves are a given if not already fitted. I recommend against a light flywheel unless this is going to be a race / rally car. With any cam with longer duration (like a D grind camshaft) and twin SU carbs the idle will be erratic. The RPM fluctuations will be significant and make setting ignition timing with a timing light interesting. |
The Following User Says Thank You to 142 Guy For This Useful Post: |
Dec 13th, 2023, 19:03 | #9 | |
Junior Member
Last Online: Apr 6th, 2024 15:21
Join Date: May 2007
Location: Sittingbourne
|
Quote:
Thanks for getting back to me. I already have a 123 ignition and upgraded from single zenith to twin su's with a custome made inlet/outlet and straight through stainless exhaust system so i went from 60 hp to 80 so big improvment. i only have a 4 speed so i went for mid when getting the downpipes designed so after that grunt rather thsn the top end. I have a good guy who restores and builds engines. Has done a lot of work for Boyd Coddington, so lucky to know him! |
|
The Following User Says Thank You to DOGSTAR For This Useful Post: |
Dec 13th, 2023, 22:03 | #10 |
Master Member
Last Online: Yesterday 15:46
Join Date: Jul 2020
Location: Saskatchewan, Canada
|
Up sizing a B18 bottom with larger pistons has its issues. Because of the larger swept volume you will get an automatic bump in compression ratio. If you are already running a higher compression ratio you will need to open up the combustion chambers to reduce the CR to something manageable. At that point, setting up your squish band depth becomes even more important.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|