landi renzo igs

landi igs · Apr 28th, 2013, 18:13

hello. I'm from the Croatian and I have a problem with Landi Renzo IGS gas system. I bought it second-hand without wire diagram and conetct everything except tps (thortle position sensor) lambda sensor and rpm sensor.
The problem is that I do not know which color goes on the table. and if you could take a picture or list that color with IGS and connects to what color the car, or better yet, if you might know which wire is the signal or voltage.
thank you very much.

I wanted this to send your member Andy_Gibson but can not.
Please if you can inform him or help me because nowhere in the entire web I found nothing on the IGS.

classicswede · Apr 28th, 2013, 20:33

Hard to help when you have not said what you are fitting the system to.

The RPM wire is the brown wire on the loom and needs conecting to a coil earth.

TPS is yellow/green usualy and would be connected the TPS switch signal 0-5v

Lambda is purple wire and can only be connected to cars with 0-1volt sensor or 0-5 volt sensor. You must not connect to a wide band sensor with these systems.

landi igs · Apr 28th, 2013, 22:11

thanx, the car is alfa romeo 145 1.6 76kw.

I tried to combine something but no results, I will try this scheme tomorrow, the problem is that to me nobody knows anything about this system and even less about the scheme of the wire

I found out at Google search member with the same problem and hoped that I would get at least some help
thank you very much.

classicswede · Apr 28th, 2013, 23:32

If it is the same system as in this video

http://www.youtube.com/watch?v=O6wNpoBRwig

good luck - you will need more than just luck to make it work!!

Do you have the software and setting cable?

landi igs · Apr 29th, 2013, 15:37

I have this system, I was able to start the engine on the IGS, for quite a few rough due to too much gas (before it was the 150hp car) mine has 105hp.
I do not have a program for mapping, but there are few people who can probably fix software.

Thank you again, your information helped me greatly

Apr 28th, 2013, 18:13	#1
landi igs New Member Last Online: Apr 29th, 2013 15:37 Join Date: Apr 2013 Location: zagreb	landi renzo igs hello. I'm from the Croatian and I have a problem with Landi Renzo IGS gas system. I bought it second-hand without wire diagram and conetct everything except tps (thortle position sensor) lambda sensor and rpm sensor. The problem is that I do not know which color goes on the table. and if you could take a picture or list that color with IGS and connects to what color the car, or better yet, if you might know which wire is the signal or voltage. thank you very much. I wanted this to send your member Andy_Gibson but can not. Please if you can inform him or help me because nowhere in the entire web I found nothing on the IGS.

Apr 28th, 2013, 20:33	#2
classicswede Trader Volvo in my veins Last Online: Yesterday 21:53 Join Date: Dec 2004 Location: Anglesey	Hard to help when you have not said what you are fitting the system to. The RPM wire is the brown wire on the loom and needs conecting to a coil earth. TPS is yellow/green usualy and would be connected the TPS switch signal 0-5v Lambda is purple wire and can only be connected to cars with 0-1volt sensor or 0-5 volt sensor. You must not connect to a wide band sensor with these systems. __________________ http://www.classicswede.org www.classicswede.co.uk

Apr 28th, 2013, 23:32	#4
classicswede Trader Volvo in my veins Last Online: Yesterday 21:53 Join Date: Dec 2004 Location: Anglesey	If it is the same system as in this video http://www.youtube.com/watch?v=O6wNpoBRwig good luck - you will need more than just luck to make it work!! Do you have the software and setting cable? __________________ http://www.classicswede.org www.classicswede.co.uk

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Apr 28th, 2013, 22:11	#3
landi igs New Member Last Online: Apr 29th, 2013 15:37 Join Date: Apr 2013 Location: zagreb	thanx, the car is alfa romeo 145 1.6 76kw. I tried to combine something but no results, I will try this scheme tomorrow, the problem is that to me nobody knows anything about this system and even less about the scheme of the wire I found out at Google search member with the same problem and hoped that I would get at least some help thank you very much.

Apr 29th, 2013, 15:37	#5
landi igs New Member Last Online: Apr 29th, 2013 15:37 Join Date: Apr 2013 Location: zagreb	I have this system, I was able to start the engine on the IGS, for quite a few rough due to too much gas (before it was the 150hp car) mine has 105hp. I do not have a program for mapping, but there are few people who can probably fix software. Thank you again, your information helped me greatly

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)