Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 700/900 Series General > 700/900 Series Articles
Register Members CarsBlogs Help Calendar Mark Forums Read

Notices

700/900 Series Articles How to's and Guides for the P700/900 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

960 / V90 parking brake cable R&R

Views : 7342

Replies : 11

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Nov 5th, 2013, 01:31   #11
tosoutherncars
Junior Member
 

Last Online: Jun 28th, 2017 04:13
Join Date: Oct 2013
Location: Ottawa
Default

REASSEMBLY - PARKING BRAKE DRUMS (Cont'd)


**Edit to previous post - delete #6. You can *not* put the rotors on at this point.

#6 (revised) - With drums off, connect all cables at rear.



#7 - In cabin, ensure adjuster knob on handbrake is completely slacked off. Pull the cable forward and hook onto handbrake assembly. If using pliers, be careful not to damage the cable end and/or cable.



*Author's note; I actually did the reverse; connected the handbrake first, then put in the cotter pin in the rear end. That said, I suspect it is easier as done above; as long as the drums are OFF.

A few random notes:

A) Some have mentioned that they had trouble pulling the cables out of the aluminium subframe. Galvanic corrosion is the obvious suspect here.

Suggestion; cut off the cable just before the ferrule. The ferrule, you will notice, is crimped on, and is hexagonal. (Hint, hint.)



Assuming (of course) that you have doused everything with penetrating oil the day before... hammer a 15mm socket onto the ferrule, and twist away in either direction. (It's not threaded, you're just breaking it free.)

Mine were locked in solid, but yielded almost immediately to this treatment.



B) At the other end of that same cable (so, the outboard end attached to the caliper housing) after prying out the U-shaped retaining washer, the other ferrule was also locked in solid. When I started using the BFH on it, I noticed (rather fearfully) that the part of the caliper into which the ferrule attaches was moving along with it.

I was really afraid that I was going to break the caliper; which is exactly what happened. The ferrule, and the surrounding caliper "collar", came off together.

The good news; the collar is just a friction fit. And, added bonus, it's much easier to punch out the ferrule on the bench, than on the car. So, long and short; don't worry about everything coming apart there. Just knock it off; if the collar comes with it, it's easy to reinstall.

And finally; just a little video of what greeted me when I pulled the left-side rotor.

http://s10.photobucket.com/user/toso...1ee57.mp4.html
tosoutherncars is offline   Reply With Quote
The Following User Says Thank You to tosoutherncars For This Useful Post:
Old Nov 15th, 2013, 08:11   #12
tosoutherncars
Junior Member
 

Last Online: Jun 28th, 2017 04:13
Join Date: Oct 2013
Location: Ottawa
Post

Just to wrap this up...

Assembly is the reverse of removal, as Haynes would say. Once the cable was in, I tightened the gas tank back up, before reinstalling the exhaust (with a new middle hanger jerry-rigged from what I had on hand.)

I followed the break-in procedure for both the e-brake drums and the rear pads; a slow drive with the e-brake applied for the former, and a series of increasingly hard stops for the latter.

I didn't need to adjust the e-brake at all. (!) With everything hooked up and the adjusting nut all the way loose, the brake engages around the third click, and locks the car up tight around the 6-8th clicks. It will hold the car in Drive (no gas) on flat ground. Feels very solid.

No special tools were required; just the following:

- sockets (10-15mm mostly; 3/8" and 1/2" versions with several extensions and a wobble-joint)
- pliers, vice-grips (several), small pry bars
- Torx screwdrivers (T15, 20, 25 and I think 30)
- Flathead screwdrivers
- brake cleaner
- bearing grease

In all, it was a pain of a job; but doable, and a HUGE savings over what the garage (or God forbid, the dealer) would have charged. Just set aside a good couple of days just in case, get all your parts together first, and try to run the gas tank as empty as possible before starting!

In retrospect, I think the only things I would have done differently are: I would have ordered rear rotors, even though they weren't strictly needed in my case, and a new middle exhaust hanger, which I should have noticed was totally rusted through.

Speaking of the exhaust; I noticed when I dropped the muffler, that it had a couple of pinholes. One more thing to look for, the next time I'm at the scrappie! ;-) Or start saving up for...
tosoutherncars is offline   Reply With Quote
The Following 4 Users Say Thank You to tosoutherncars For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 08:16.


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.