Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 700/900 Series General > 700/900 Series Articles
Register Members CarsBlogs Help Calendar Mark Forums Read

Notices

700/900 Series Articles How to's and Guides for the P700/900 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

V90: Drivers Window Switch Replacement

Views : 10099

Replies : 0

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Jun 1st, 2014, 18:50   #1
CTCNetwork
Forum Support Team
 
CTCNetwork's Avatar
 

Join Date: Dec 2004
Location: Notts, UK
Default V90: Drivers Window Switch Replacement

Hi,

Drove to work a couple of weeks ago and seeing a colleague leaving needed to make sure he had all the bit I had prep'd for him s wound the window down. Parked up and attempted to close the window.
The clue is in the "attempted".. Down triggered a slight response from the window gear but not up.

After faffing about for a while it was obvious the window was staying. Popped to DPF who promptly disconnected the switch and wound up the window. Switch was confirmed as the culprit.

Called Braydons who has a switch panel in and they sent it complete. Different colour to mine so decided the swap switches. After al, how hard could it be!!!

So to get at the panel and remove it it is best to pull the door card.
First you need to pull the bottom door clips:



That one near the front is inset and needs a small screw driver to get it out:



Next comes the door pull removal:



Lever out gently the cover plate with a small screw driver:



You get to see the two torx head screws holding the pull and door car in position. Sometime, if a dealer has already been here they'll use a bit of mastic to stick the plate in position!:





Remove the rear red warning lamp. Either as here by pulling the lap out of the door card, or you can also just disconnect the cable and leave the lamp in situ:





Carefully remove the door release trim:





You should now be able to pull the lower part of the card away and then lift the whole off the door:





Now we can see the switch panel with it green surround in place. All the plugs are different. None will plug into any other socket/switch point:



After careful removal of each of the plugs for all of the switches we can remove the panel from the door card. Remove carefully the whole switch panel out. Be careful as it is in two halves clipped together (and best to stay that way!):



This gives ease of access to remove the green surround using the clip points (one on each side) to remove it:





This brings us neatly to the offending switch. The switch are held in place by plastic clips that "grab" the switch.:



The clips are brittle, being 16 odd years old. Releasing on clip pushes the switch against the other making release difficult. You will also see that the gap at each end is different. It makes little difference which end you start from as to your success. This really unnerved me as I could see that one of the clips would undoubtedly break. So I decided to pop the switch in a warm place for a while to help "soften" any brittleness. An hour was obviously not enough as, on removal the clip on one side gave way slightly.
My remidy was simple. Shore up that side of the switch and clip. I used the plastic case from a recent micro SSD card delivery and used two pieces together and slid then down the space between switch and switch socket on the panel:





Once back in, refitting is pretty much the reverse of the above. Things to watch out for are remembering to connect all your cables. When fitting the door card back raise the top inner edge above the metal of the door inner panel and at an angle - rear up to allow the card to be slid back into position. Make sure the position is correct so you can get 1) the bottom clips back and 2) the two screws back.
The front of the three clips is a devil to return. I found a little mastic on a slim ratchet driver holding the clip was best and hold the door card onto the door to allow correct fitting.

Voilà, one working drivers door window again.

Des. . .
__________________
Density:- Not just a measurement ~ It's a whole way of Life.! ! !
I drive a Volvo, Please Don't Get In My Way!
He shows up. People die. He vanishes.
People should not be afraid of their governments.
"He'll deliver more justice in a weekend than 10 years of your
Governments should be afraid of their people... "V"
courts & tribunals. Just stay out of his way." "I plan to."
CTCNetwork is offline   Reply With Quote
The Following 2 Users Say Thank You to CTCNetwork For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:59.


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.