|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
Information |
|
Voltage supply issuesViews : 1136 Replies : 17Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 11th, 2017, 22:04 | #11 | |
Experienced Member
Last Online: Today 14:49
Join Date: Jun 2007
Location: L/H side
|
Quote:
The Analogue signal goes from pedal pin 2 on the white wire to the CEM and is then carried over the network to the ECU . I have always found replacing the white wire and terminals has fixed it .
__________________
My comments are only based on my opinions and vast experience . |
|
The Following User Says Thank You to Clan For This Useful Post: |
Dec 15th, 2017, 18:48 | #12 | |
Junior Member
Last Online: Jan 11th, 2019 06:37
Join Date: Jul 2017
Location: Tremelo
|
Quote:
Thanks in advance! Update, I found some online help but don't have the right tools to disassemble the wire, will go to garage and hope they will lend me the tool.. Will update tommorow. Thanks again! Last edited by hansC30; Dec 15th, 2017 at 21:21. |
|
Dec 16th, 2017, 16:01 | #13 | |
Experienced Member
Last Online: Today 14:49
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
The Following User Says Thank You to Clan For This Useful Post: |
Dec 21st, 2017, 19:27 | #14 |
Junior Member
Last Online: Jan 11th, 2019 06:37
Join Date: Jul 2017
Location: Tremelo
|
Thanks! I was able to dissasemble everything but I have no idea how to look for the correct type of terminal online.. Went to local garage but they don't know the type, and I can't find it in VIDA either.. Do you have any idea how to look for these terminals? A serial number would come in handy :-)
|
Dec 21st, 2017, 20:32 | #15 | |
Experienced Member
Last Online: Today 14:49
Join Date: Jun 2007
Location: L/H side
|
Quote:
The terminals come already crimped to a piece of wire about 6 inches long
__________________
My comments are only based on my opinions and vast experience . |
|
Dec 21st, 2017, 21:33 | #16 |
Junior Member
Last Online: Jan 11th, 2019 06:37
Join Date: Jul 2017
Location: Tremelo
|
Ok, I'll go ask tomorrow. Thought I could juist build the cable myself with the correct terminals:-) Thanks for all your help!
|
Jan 28th, 2018, 19:02 | #17 |
Junior Member
Last Online: Jan 11th, 2019 06:37
Join Date: Jul 2017
Location: Tremelo
|
Sorry for the late update, haven't driven the car a lot lately. I went to garage but they could not find the entire cable, only the connectors which you can only buy per 10, 2.5euros each(!) . I disconnected and reconnected everything and haven't had any issues anymore so I decided to leave it like this for a while. 50euros plus cost of tool to connect these terminals was a bit too much for now😉
|
Feb 9th, 2018, 20:13 | #18 |
Junior Member
Last Online: Jan 11th, 2019 06:37
Join Date: Jul 2017
Location: Tremelo
|
Just replaced the cable after getting I limp mode couple of times again. Found the cable in the third Volvo garage I went to☺️only the connectors with small piece of wire on it though. What a b***** to replace these cables!! Hope this fixes it!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|