|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
Information |
|
S40 will crank but not start, just had new timing beltViews : 772 Replies : 10Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 13th, 2018, 15:38 | #1 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
S40 will crank but not start, just had new timing belt
Hi all hoping for a bit of advice from the Volvo wizards. I've got a new shape Volvo s40 2.0D sport. I have just changed the timing belt on it following all the correct steps and when I try to start it she'll crank but won't start.
I made sure I put the dowel pins in the correct places and that everything lined up but without any proper timing marks its hard to tell if it is properly lined up. I am certain I did everything properly but it could very well be out of time What is the best way for me to check the timing on it? is there a way? I am currently waiting for it to charge as I have cranked it so much but it will crank over and at times it cranks over faster and faster till it settles down and has enough. Has anyone got any ideas how I can check everything is in time or what else it could be? |
Dec 13th, 2018, 21:36 | #2 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
Right I've gone through and checked the timing again by getting the two dowels locked into place and putting the timing belt back on just to make sure so unless it can still be out of time with the dowels in its right. After all of that it still won't start!
I'm running out of ideas here. My only two theories are that it is something to do with the crank sensor at the bottom which is either faulty or the notch on the tdc ring is in the wrong place as that did come away from the reluctor when I took it off. Could this be a cause? Or there is air in the fuel like. Has anyone got any ideas? |
Dec 13th, 2018, 22:01 | #3 | |
Premier Member
Last Online: Yesterday 00:05
Join Date: Aug 2009
Location: birmingham
|
Quote:
__________________
940s - 2l / 92 < gone&missed s401.8 xs auto <gone >V50 2.4SE Geartronic aka "the new money pit" "skyship007 has now been successfully added to your ignore list. "." |
|
Dec 14th, 2018, 08:13 | #4 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
Yes that's not a bad idea but the only thing is where should it go in relation to the. Reluctor that slides into the crank at the bottom ? The only marking in a notch on it for I assume the tdc sensor to read. Someone did say to me that it shouldn't really matter it's location as it's just used to sense rpm
|
Dec 14th, 2018, 10:36 | #5 | |
Experienced Member
Last Online: Yesterday 23:47
Join Date: Jun 2007
Location: L/H side
|
Quote:
Also the magnetic timing ring is very delicate you must never touch it with your hands and if you knock the edge it could ruin it .. with the locking pins in you should put the cambelt on then tension it BEFORE tightening the crank pulley bolt to get the timing perfect ...
__________________
My comments are only based on my opinions and vast experience . |
|
Dec 14th, 2018, 10:52 | #6 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
Yes I absolutely did put those in and double checked I got it right however I did knock the magnetic ring and that tiny magnetic key in the end of the crank and touch it with my hands. D'oh. So that could be the issue. Would you recommend I replace them both just to be on the safe side?
|
Dec 14th, 2018, 11:07 | #7 | |
Experienced Member
Last Online: Yesterday 23:47
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
Dec 14th, 2018, 12:24 | #8 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
Ok I'll have a look at buying one then. Any idea where I get one from or will the local Volvo dealership be the best bet? Yes haha I worked that out after starting at it for a bit. Would you say it's worth buying a new magnetic key for the crank end too?
|
Dec 14th, 2018, 12:27 | #9 |
Experienced Member
Last Online: Yesterday 23:47
Join Date: Jun 2007
Location: L/H side
|
the dealer can get one the same day if you order early enough , the key should be ok unless you have damaged it ..
__________________
My comments are only based on my opinions and vast experience . |
Dec 14th, 2018, 13:42 | #10 |
Member
Last Online: Jan 18th, 2024 08:54
Join Date: Aug 2014
Location: warwick
|
Awesome I'll get into them then. Thank for all the help and I apologise for any silly questions it's not an engine I am familiar with, I'm use to using a sledgehammer in the old redblock haha
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|