Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 700/900 Series General

Notices

700/900 Series General Forum for the Volvo 740, 760, 780, 940, 960 & S/V90 cars

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

How To: Front End Polybush Volvo 940

Views : 1575

Replies : 5

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Aug 22nd, 2019, 21:57   #1
360beast
I'm addicted to my 360
 
360beast's Avatar
 

Last Online: Today 09:09
Join Date: Feb 2012
Location: UK
Default How To: Front End Polybush Volvo 940

I thought I would make a little how to guide for the front end polybush job a 940 as Mark asked me to and I know a couple of people including my mate will want a little guide on how to do it so here goes.

You will need:

Superflex SF422-2013KSS
Superflex SF422-2012K
Superflex SF422-1023KSS
Classicswede Droplink Pin Kit https://www.classicswede.co.uk/Front...4_8228034.aspx
Classicswede Lower ARB bush Kit https://www.classicswede.co.uk/Front..._20024697.aspx

Tools:

Jack
Threadlock
Breaker Bar
Torque Wrench
Pry bar
15mm socket
17mm socket
18mm socket
19mm socket
21mm socket

Firstly you need to jack one side of the car up and remove the front wheel... still with me?

You then need to remove the pin and undo the bottom ball joint securing nut. Undo the 2 bolts that hold it on the strut leaving the joint in the arm. As per the photo below but I did it the other way around, up to you which way you do it.


20190816_140154 by Luke Ryland - Flickr2BBcode LITE

Undo the spaceship bush bolt you will need the breaker bar and 17mm socket, dont remove the bolt fully just leave a couple threads in the arm.

Then put the pry bar between the chassis and ARB and push down, using the 15mm socket and ratchet undo the ARB droplink to ARB nut. The pry bar will stop the arm jumping up and potentially causing some damage.


20190816_140148 by Luke Ryland - Flickr2BBcode LITE

Remove the bolt from the rear chassis bush using the 18mm spanner and 21mm socket, you will need to use the breaker bar to start it off.


20190816_140159 by Luke Ryland - Flickr2BBcode LITE

Then do the same with the front bush, I can't remember the nut size I think 18mm spanner and 17mm socket.


20190816_140205 by Luke Ryland - Flickr2BBcode LITE

Then the whole lot will drop off in one go, you now need to remove the ball joint from the arms. Use two hammers and hit either side of it to remove.


20190816_140918 by Luke Ryland - Flickr2BBcode LITE

Now then, if like me you rebuilt a spare set of arms and fitted all of the bushes before fitting. So you can remove the old and install the new instantly no messing around.

You will need to press the old bushes out except for the spaceship bushes which you can use a flat blade screwdriver to remove. You will probably have to clean up the spaceship bush mating face as it was quite rusty and pitted on mine where the water sits.

To fit the chassis bushes they will need pressing in to the arms, I have a hydraulic press at work which I used to remove and fit the bushes but you could do it by burning the rubber out, cutting the sleeve and then pressing it out with a vice.

The spaceship bushes can be loosely assembled by hand. Make sure to apply grease to all the contact surfaces of the bushes.


IMG-20190813-WA0009 by Luke Ryland - Flickr2BBcode LITE


20190814_173928 by Luke Ryland - Flickr2BBcode LITE

Now Haynes it and refit in reverse.

To torque up the bolts if you use rubber bushes then you need the weight of the vehicle on its wheels, polybushes you don't need it to be as the metal sleeve you insert in the bush spins independently so no need to.

You need to apply threadlock to all the bolts you have removed from the bushes!

Refit the ball joint to the strut, this has a two stage torque setting

Stage 1: 30Nm
Stage 2: angle tighten 90 degrees

85Nm for front metal sleeved bush


20190816_142137 by Luke Ryland - Flickr2BBcode LITE


120Nm for the rear chassis mounted bush


20190816_142117 by Luke Ryland - Flickr2BBcode LITE

100Nm for the spaceship bushes


20190816_151527 by Luke Ryland - Flickr2BBcode LITE

Fit the control arm and ball joint back together and tighten to 70Nm and refit the locking pin.

The droplink pin bushes just need fitting like a normal rubber one, the bottom pin bush I haven't done on mine yet but you will just need to remove the rubber and insert it in to the droplink. The rubber may need burning out I'm not sure, I believe they are bonded so will require burning out. Tighten the ball joint bolts until tight, no torque setting is supplied for these in the Haynes manual.

Now it will need a wheel alignment.

The settings are...

Castor: 5 degrees + or - 1 degree
Camber: 0.1degree + or - 1 degree doesn't say negative or positive so I assume negative.
Toe: 2.2mm + or - 1mm toe-in

Now then, I have had an issue with my radius arm to chassis bush where it makes a horrible knocking noise, I took it back off and discovered that the sleeve that you insert in to the bush pushed all of the grease out of the bush! As it runs dry the crosshatchings rubbing on the sleeve make the noise.

So I have drilled a 5.2mm hole through the arm and polybush, tapped an m6 thread and fitted grease nipples. Hopefully once I get a grease gun and some grease this will solve it.


20190821_124327 by Luke Ryland - Flickr2BBcode LITE


20190821_124456 by Luke Ryland - Flickr2BBcode LITE

Here is the bone dry bush I discovered upon removal.


20190819_172244 by Luke Ryland - Flickr2BBcode LITE

Now enjoy your 940 actually being able to go through corners at speed!

Last edited by 360beast; Aug 22nd, 2019 at 22:06. Reason: Photos in the wrong place and spelling
360beast is offline   Reply With Quote
The Following 4 Users Say Thank You to 360beast For This Useful Post:
Old Aug 22nd, 2019, 22:10   #2
griston64
Premier Member
 
griston64's Avatar
 

Last Online: Yesterday 22:45
Join Date: Jul 2012
Location: Lenzie
Default

Excellent write up Luke
__________________
V70 D5 SE Geartronic 215bhp Saville Grey 2012MY
940 LPT Manual 1996
griston64 is offline   Reply With Quote
The Following 2 Users Say Thank You to griston64 For This Useful Post:
Old Aug 22nd, 2019, 22:50   #3
Laird Scooby
Premier Member
 
Laird Scooby's Avatar
 

Last Online: Today 11:33
Join Date: May 2012
Location: Lakenheath
Default

Very impressive write up Luke!
__________________
Cheers

Dave

Next Door to Top-Gun with a Rover 827 Sterling and a 765 GLEa V6!
Laird Scooby is online now   Reply With Quote
The Following User Says Thank You to Laird Scooby For This Useful Post:
Old Aug 23rd, 2019, 11:58   #4
827Roverman
VOC Member
 

Last Online: Yesterday 12:03
Join Date: Jan 2016
Location: UK
Smile

Quote:
Originally Posted by 360beast View Post
I thought I would make a little how to guide for the front end polybush job a 940 as Mark asked me to and I know a couple of people including my mate will want a little guide on how to do it so here goes.
/snip
Excellent! well done Luke, good write up and photo's, now when are you coming to do mine , David.

Last edited by CTCNetwork; Jun 30th, 2020 at 14:58. Reason: No need to quote, just reply.
827Roverman is offline   Reply With Quote
The Following 4 Users Say Thank You to 827Roverman For This Useful Post:
Old Aug 23rd, 2019, 16:56   #5
360beast
I'm addicted to my 360
 
360beast's Avatar
 

Last Online: Today 09:09
Join Date: Feb 2012
Location: UK
Default

Quote:
Originally Posted by 827Roverman View Post
Excellent! well done Luke, good write up and photo's, now when are you coming to do mine , David.
Haha Thanks David, if you want me to I can overhaul the arms that came off mine for you with polybushes and send them up to you in exchange for your old ones plus some money for my efforts?

I have also managed to get a set of snow tray clips so I will have a go at making a pair for you too.
360beast is offline   Reply With Quote
The Following 2 Users Say Thank You to 360beast For This Useful Post:
Old Aug 23rd, 2019, 18:15   #6
jpliddy
VOC Member
 

Last Online: Yesterday 19:57
Join Date: Dec 2006
Location: stoke on trent
Default

excellent tutorial from 360 beast !
jpliddy is offline   Reply With Quote
The Following 2 Users Say Thank You to jpliddy For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 11:35.


Powered by vBulletin
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.